# 1
Draw-Tite Drawbar for 1-1/4" Hitches - 5/8" Rise, 1-1/4" Drop - 7" Long - 3.5K
Items packed well delivered on time. Doesn't get much better that that.
The service is great and so is the price. Box came damaged but if it installs as easy as the last one I bought from etrailer I will be very happy!
# 2
Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 7-1/4" Long - 3,500 lbs
I installed this on my 2015 Honda Accord for the purpose of pulling my small aluminum fishing boat and trailer. Works great!
Drawbar looks great and will be using in next two days. Thanks!
# 3
Curt Class III Ball Mount with 1-7/8" Ball - 2" Drop - 3,500 lbs
Works perfectly. Fast shipping. Very Satisfied.
Very pleased with etrailer. Very easy to order from website. Fast delivery, easy to install ,perfect fit . Thanks. .
# 4
Curt Class II Drawbar - 3-1/8" Rise - 11-1/4" Long - 3,500 lbs
Used on my 1999 Dodge Intrepid's CURT 12006 Class II 1.25 in. Receiver Hitch: 350lbsTW/3500 lbs GTW. I use this Curt Class II Drawbar - 3-7/8" Rise - 11-1/4" Long - 3,500 lbs to tow a 3,500+ GTW dual axle trailer. I have used it with the trailer FULLY loaded and it performs EXCELLENT. You have to make sure the trailer is loaded correctly so as not to put too much down force on the tongue/drawbar. I was skeptical that the SOLID 1.25" bar would not take the load, but it is super strong. I chuck it in the trunk when not in use to protect passerby's shins, but it sticks out far enough clear the Intrepid's bumper, and is solid with a 2" ball (required a bushing). etrailer got it out fast at a good price! I would totally purchase this again from them.
Every part excellent quality. Perfect fit, all parts were exact for my vehicle. Watched the video on youtube for wiring and being a mechanic for over 50 years was able to connect signal lights all from driver side of harness. Instead of leaving plug inside trunk I wired through the rubber outlet to the back of the hitch ready for use. Very happy highly recommend etrailer.
# 5
Curt Class II Drawbar - 5" Rise - 9-5/8" Long - 3,500 lbs
I am an infrequent trailer user, but getting my daughter home from college was necessary in March. This drawbar fits my hitch and utility trailer well, did exactly what it is supposed to do, and was the last thing to be concerned about right then. I have a '11 Mini Countryman S with a Class II receiver from Mini Fini, (which cost twice as much as a Curt) where the hole is flush with the fake grille near the bottom of the bumper cover, so I needed the long bar to reach out past the bumper. The Curt receiver for that car hangs visible underneath the bumper (ugly), which also increases the lever arm on the receiver beam and would have needed an even taller rise. (Curt take note!) All just part of the kit to create an occasional 1 ton pickup out of my Mini, leaving the "bed" at home most of the time.
Purchased for a Hyundai Elantra. After a 2" ball is mounted, there is about 7.5" from the top of the square shaft to the top of the ball. This is what was needed to get the center of the ball 18" off the ground for most U-hual trailers. This design has no plate edge protruding below the square shaft. This helps reduce scraping when going over bumps, which is an annoying issue with my other ball mount. I would have much preferred the euro ball mount, which has a nice 45' bend to avoid scraping, and a ball that will never vibrate loose, but one was not offered with this much rise. The ball mount is well made of solid steel, not a hollow tube. Finish quality is excellent. The mount does not come with the locking pin needed and so that must be ordered separately with the ball. Item was packed a little loose in the box and was clanking around with the other item I bought, but they did not get scratched up.
# 6
Draw-Tite Drawbar for 1-1/4" Hitches - 5" Rise - 10" Long - 3,500 lbs
This is the correct towbar for a Toyota Prius C. The towbars that are available from U-haul (3 1/8") and other hardware stores are too low to the ground for most trailers. I tow my Harley Dyna on a motorcycle trailer behind my Prius C with no problem. Save yourself the grief. I bought three readibly available tow bars until I found the right one. The 5" rise, 10" long works perfectly. This is an incredibly strong drawbar.
Worked perfectly Did have to grind off the paint and a nit of metal to fit in the reciever though.
# 7
Curt Class II Drawbar - 5" Rise - 11-5/8" Long - 3,500 lbs
I was in need of a hitch higher than the standard 3 or 4 inch riser and spoke with Samatha B, after a couple of emails she found a 5 inch riser for my 1 1/4" receiver. Just what I needed and a happy customer. Received very quick and good sturdy quality. Thanks again!
3.5 stars. Product looks like it should perform as advertised, but it arrived with several chips in the paint. This is most likely due to improper surface preparation and cleaning before the powder coat was applied. As you can see in the photos, there is already some surface rust on some of the areas, including the hole for the hitch pin. Ultimately the paint will get scratched up from use, but it would be nice to see some extra attention to detail from the factory.
# 8
Curt Class II Drawbar - 3/4" Rise, 1-1/4" Drop - 9-3/4" Long - 3,500 lbs
This draw bar in perfect for my John Deere X738 tractor. What I like about it is the ¾” rise it keep the draw bar height at about the same as the factory frame so the attachments height remain level. Thanks for the great product.
Not much you can say about a bar with a piece of flat metal welded to it; well made looks good. What is really important is that e-trailer is fast, friendly and knowledgeable. I've ordered from them anytime I needed a trailer/RV part.
# 9
Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 9-3/8" Long - 3,500 lbs
I needed to tow a trailer with a 2" ball. My original ball mount has a 1 7/8" ball installed. I had previously tried to change a ball on a hitch and destroyed the nut and damaged the underside of the ball mount. The lock washer had done a great job in keeping the nut from coming off. I dreaded trying to remove my 1 7/8" ball to install a new one that I would only use once. I decided to buy a new ball mount and mount the new 2" ball. This ball mount is so inexpensive that I realized I could have both ball sizes permanently mounted for use in either ball size.
I wasn't sure what type of ball mount I needed for my new Mazda CX-9, so I had to call a representative. The first time I called, the very knowledgeable gentlemen told me exactly how to measure my SUV to figure out the drop I needed. I called back the next day and talked to a lady who helped me figure out exactly what I needed. This is my second purchase from etrailer. The first was a hitch for my old Honda Odyssey, which was also a great experience. The employees are so helpful, the video tutorials on the web site are fantastic and the prices are great. etrailer.com is the first place I go to look for trailer and towing supplies!
# 10
Curt Class II Euro Style Drawbar with 2" Ball - 2-3/4" Rise - 3,500 lbs
It is heavy duty and well-built. I am not disappointed at all and I get comments everyone smile from people who are used to traveling overseas asking where I got the European style hitch from. The only downside is the lack of interchangeability in the size of the ball itself but I don’t think that’s a big deal because I set it up for what I need it for and keep a vehicle vehicle for longer periods of time.
Solid, heavy as heck. Bought this model because 1) I only have 1 lightweight trailer (Malone xtralight, also purchased from etrailer at the same time) and it’s light weight. 2) I am stuffing this into an adaptor also bought from etrailer to further stuff into a receiver also purchased from etrailer. 3) All this is on the back of my 2018 Subaru Outback. Beings that it’s a Subaru it’s not going to be used to drag a huge or heavy trailer. I’ll repeat this part in my review of the adapter, buy probably from etrailer, a receiver lock that is sleeved, to be both 1/22 and 5/8 and long. That way if you don’t want this sticking way out the back (shin killer) you can use 1 lock and go all the way through receiver/ adapter/ and this ball mount. Otherwise buy you’ll need 2 locks 1 for receiver to adapter 5/8 and a second 1/22 to go through adapter into this unit. A side benefit is it’s just different. It’s not an everyday boring looking ball mount, it’s heavy duty so why not.
# 11
Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 6-1/4" Long - 3,500 lbs
All equipment was delivered on time. Hitch, wiring harness, receiver and ball. Watched video's on installation of harness and hitch. Went down to my garage and installed both with the help of my girlfriend. Very satisfied with the products and the installation. etrailer supplied the goods and the knowledge. I am very happy that I went this route.
Received hitch receiver and accessories in perfect condition. Installation was very easy. (Especially if you have a lift). I fit this on my 2014 camry SE. Everything fit perfectly. The installation video helped a great deal with measurements. Shipping was fast. I searched around for the best price and etrailer.com had the lowest overall price. Big thanks.
# 12
Drawbar for 1-1/4" Hitch - 2-5/8" Rise, 3-1/4" Drop - 7-3/16" Long - 3.5K
The hitch works great. The service was excellent!!! I'm going back and having a hitch put on my other car soon. Thank you.
Everything was perfect.! Nice paint, package, and fast shipping.! Im satisfied.!
# 13
Reese Trailer Hitch Starter Ball Mount Kit
I needed an very specific ball mount(class I, 1/2" rise, 2" ball). etrailer had what I needed in stock and available to ship next day. I had the thing ordered in 60 seconds. Wish I wouldn't have waisted my time and gas shopping at my local hardware stores only to find they didnt have what I needed.
# 14
Brophy Drawbar for 1-1/4" Hitches - 5-1/2" Rise, 6" Drop - 7-1/4" Long - 3.5K
I just purchased a new hideaway hitch system. But the hitch sits only 15 inches off the ground at best. And, my trailer coupling is 22-23 inches off ground. So l needed 7-8 inches of rise on the new 1.25 inch receiver system. Internet research took me to etrailer and the Brophy hitch. I got 5.5 inches with the Brophy hitch, the highest available for a 1.25 inch receiver I could find. The others are limited to 5 inches max. I added another 1.5 inches with your Curt shock absorbing hitch. Voila, with a combined 7 inches of rise and on level ground the trailer now rides perfectly level!!!! Both parts were very easy to connect. Delivery was speedy. Thank you for saving the day and my investment in an expensive new hideaway hitch!
Quality parts, but the extra rise with this and the Curt Rocker Ball still wasn’t enough to avoid scraping the top of my inclined road while towing my boat.
What our customers are saying:
"WOW! I am impressed! I called to place my order and real person answered, spoke perfect English, albeit a slight southern accent, and my order was sent within a day, shipped quickly and I had it a few days later. I saved over a hundred dollars over local and installed it my self. I cant imagine how that they could do any better. THANKS!"