Best 2023 BMW X3 Trailer Hitch Ball Mounts

The product is good but a bit tideous and after installing it my bracket fell and it was a pain to get replace it support made me buy the replacement pieces and the bracket didnt come with just the bolts, and at the end they told i have i had to buy the whole unit because based on their system my truck didnt have issues with installement and the manufacturer didnt supply that bracket cause it special order so in general i dont recommend in my choice better to get it welded.

Working in the sand and grass of my driveway my wife and I installed our new etrailer receiver hitch. Great fit and finish! Went right on as described in the online guide. Hitch required a spacer washer on top back bolt attachment point. Taped it on so it would not move while lifting in place and it stayed right there! Used a car jack to raise up and hold the hitch into the underside of the trunk tighten the bolts and reattached the tail pipe done. Now we can pull our Sunfish Sailboat any where the car will go.

Strong and seems to be well made and well finished. One-inch ball mounting hole. I used this for a Curt hitch mounted on a 2014 Forester and pulls a small Harbor Freight trailer. Perfect height and trailer is level. Warning - don't get their hitch pin, it does not have a hole for a cotter pin, only a weak clip that I would not trust.

I searched the internet to put a hitch on my 2016 Chevy Equinox and found an instructional video from eTrailer.com where they installed on my exact car. I decided to go with eTrailer.com because they answered all my questions and because of the video-I support businesses that go the extra mile with these videos. Shipping was quick and well tracked, however, the box was flimsy and the one end of the hitch had come out of the box side and the ball mount could have easily come out of that hole during shipping. If I were eTrailer.com I'd charge an extra couple of bucks for more sturdy boxes-people will still buy as eTrailer is a well-trusted brand and this would overcome a lot of the negative reviews you'll see on their site about this shipping issue in their own reviews :-) I installed the hitch by myself (definitely recommend help as two people holding it up to the frame makes attaching 100% easier) in about 45 minutes total (out of the box, read instructions, review video again and installation complete). All hardware went on with no issues. Great quality hitch! I also bought the lesser expensive wiring assembly because most recent equinox's come hitch ready with pre-wired assembly in the left side compartment-snap and done. Picked up a new trailer at Home Depot within days and drove 5 feet and the clacking was horrible. I had always had a welded hitch before buying a hitch that took a ball mount. I really thought something was wrong and when I searched the internet that night it turns out this is very common. However, all you need is some sort of hitch "silencing" device. The number of options will drive you mad but I went with the Roadmaster Quiet Hitch and it did the trick for much less than most of the other options. If I were eTrailer.com I'd have that as one of the RECOMMENDED add-ons and explanation why its super-worthy when customers are buying a hitch. Would have saved me the time and hassle of dealing with it later and the extra shipping charge for buying after the fact when I got free shipping for the other items the first time :-) All in all, I'm super, super happy with my hitch, wiring assembly, ball mount, ball mount locking pin and the hitch silencer. Buy with confidence from eTrailer.com Paul R., Syracuse, NY

Easy install. Some of the panels separation are problematic but easier to install than planned. Looks great on the vehicle. Hope it meets my towing expectations.

The hitch and ball mount are excellent quality. My concerns are twofold. The hitch is so heavy that I had to take it to my mechanic to have it installed. Minor cost and inconvenience, but the hitch for my previous F-150 was just as sturdy, but easy to install myself (albeit with higher ground clearance). My concern about the ball mount is that the factory told me erroneously that it could not be reversed for a drop, so I returned it. This order is for the replacement after I was finally correctly told it could be reversed and how to do that. Ball mount would have been a 3 for that reason, and overall hitch and ball mount quality a 5. So I averaged them.

Part of my 2005 X3 Trailer hitch package at their recommendation and very satisfied (see my hitch details 13573 above)

This is a great all-purpose hitch. I've used it to mount a heavy-duty bike rack and a steel T-rack to carry a canoe as well as lumber. Most recently I hauled 5 x 8 cargo trailers full of plants, then furniture for a 600-mile move. It was simple to use, problem free, very strong and sturdy. Now that I live on some acreage, I see a trailer in my future, so this will get a lot more use. I drive a 2013 Tacoma, so this is a good size hitch at a good price with sufficient capacity for my needs. I do use a key lock for the hitch as well.

It's as advertised and works. It comes as shown in the picture set for a drop. If you want to flip it over to get a lift you are going to need some long wrenches. The nut holding the ball is on there extremely tight.

My order was missing installation parts, but the etrailer team were quick to correct the issue. Even without a lift, I was able to install the receiver and brake light cable quickly, thanks to their extensive video libray.

Just as advertised and solves my problem of trailer tongue level to hitch position. Delivered on schedule with no hiccups. Fits perfectly in the 2" factory receiver on my Jeep JKU. The 2" ball in the picture is a reused one not new which is why it has rust on it.

I placed my order at 11:24 am Monday. At 1:07 pm, I was informed that it had shipped. Furthermore, though I requested Standard shipping, George went ahead and sent it Express. I got my ball mount today, three days after I ordered it. Now if that's not the way business should be done, then what is? I'm all about getting the job accomplished, sooner the better, and etrailer.com is my kind of company! I have bookmarked their site, and I won't hesitate to shop with them again. BTW, the ball mount does exactly what I needed done, my boat trailer is nice and level now, not pointed at the sky like before!

We sold our small motor home and purchased a small travel trailer. This hitch provided a perfect solution to how to use our bike rack while towing the trailer. It even allows room for the pickup tailgate to be lowered without removing the bikes from the rack. The hitch is very hefty with a high weight limit - plenty for the GVW of the trailer (7,000#) plus 125# of rack and bikes.

This has been an amazing multipurpose ball mount. We purchased this to use with our Hollywood Bike Rack and also to connect onto our boat. We weren't sure if this would work, but it was awesome. It is very well built and We had to make some minor adjustments to the position of our boat on the trailer so the turning radius of the bike rack that was attached would clear the truck. This is very well made and solid.

Excellent hitch easy installation.It only took me about an hr and half to install from start to finish

All I really needed was the ball mount/hitch. The whole package was a little pricey but I figured I could use the other stuff (locking pin, hitch cover, storage case) anyway so I bought the package. The locking pin key broke after a week and I had to drill the lock out to remove it. Then I saw I could have purchased what I needed at my local auto parts store for about 1/3 what I paid for this. Definitely what I should have done. No problems with the actual ball and hitch though.

Sooooo....you sent me a product that was somehow put together backwards and I cannot take them apart somehow the ballhitch is stuck on the male portion backwards and defies gravity and doesn’t need a pin to stay on(becaue thier is no where to put the pin in cause it’s backwards

Have done about 5k with this hitch, just once with a 4500lb camper but mostly with a 3000lb cargo trailer. The former in a highly raised position and the latter in the absolute bottom position. The hitch has worn very well and shows no signs of excess wear, save for the surface of the 2" ball, but it's not concerning. On a Jeep Grand Cherokee with a stock suspension, this seems to give the right balance of range of adjustment without dropping so low in the lower configuration as to scrape through dips, though it can still be done on very sharp dips with the hitch on the lowest setting. Overall, very pleased with it and love that it's lighter than steel and won't rust.

I purchased Curt's 6" drop ball mount for my 2012 Jeep Wrangler Sport which is not lifted but has 32" tall tires. The utility trailer I plan to purchase recommends a 12" tongue/ball height for level towing. The Curt 6" drop ball mount places my tongue/ball height at 13.5" which is acceptable. The bottom of my tow ball mounting nut is now 12" above the road surface. Plenty of clearance for safe towing. I'm very pleased with the quality and functionality of my Curt ball mount. I'm looking forward to purchasing a utility trailer soon. I think it will tow very nicely using my Curt 6" drop ball hitch.

I bought this on my knowledgeable brother's advice - he gave me the exact order number and link to buy from etrailer! I had it installed locally, without complications. I use my truck mostly to haul my horse or my friend's two donkeys in my 14-foot stock trailer. I have no complaints, the hitch does what it's supposed to do.

Very happy with this ball mount - provides just the amount of drop we required for a level tow of our GeoPro travel trailer by our RAM2500. Plus, the extra length not only allows a tighter turning radius, but also allows us to lower the truck tailgate without having to detach the trailer. Huge improvement on all accounts for us compared to our prior setup. The product is well built and I'm confident will provide us years of good use.

Your packaging it's lousy, package arrived with a receiver size hole in the end of box . Guess what the box was empty . This is the second time I have had problems with your company !

My usage of your hitch is a bit unusual, I think. I pull a two ton roller with my Ram and I've used your cushioned hitch to smooth out the process. The roller Lunette just dropped over a 2" ball and then banged and jerked on the ball neck. Check out the photos for my adaptation.. I can flip it over and use the 2" ball! Have enclosed some photos. The cushion is holding up very well and it takes a beating!! Thanks

Makes for a great hard-core dirt road set up with a 3000 pound trailer, in conjunction with the Curt rocker ball, Towing with an F150 over many miles of washboards, down through washes where the road was washed out, etc. Really makes for a gentler set up on the equipment in the trailer and the truck. Thanks a lot E-trailer!

I am very happy with my trailer hitch receiver from etrailer. I installed one on my 2011 Toyota rav4 for towing a small teardrop trailer I made during the pandemic. I also purchased a wiring harness to power the trailer lights from etrailer and after some doing have it working well. The cost of doing it myself was a small fraction of having the dealership do the work. The hitch receiver is easy to install as there are pre drilled holes to receive bolts in the frame. The wiring is a bit more complicated but I did it. God bless online videos. I'm happy with the results.

Hitch ball works flawlessly with my trailer. Fits our hitch receiver just fine. Has the typical subpar black paint finish that chips easy though. Otherwise I would give it 5 stars.

Let the packing/shipping department know they should've used a bigger box and packed it differently? Kinda disappointed as this isn't the first time stuff has been battle-scarred before I get it. Considering my next steps.

Great service

This is exactly what I needed for my front end mounted receiver.

As advertised and quick delivery, I am an Etrailer fan!

Excellent product! With the three different ball sizes, this tri-ball mount gives you a lot of flexibility. Gone are the days of having several different ball mounts to fit different tongues. High quality construction makes this an excellent investment.

definitely solid as a rock

First of all, the products you find at etrailer are not your garden variety, home depot kind of fair. Much higher quality and grade/weight ratings. So to be able to get hard to find items and then by orderring at least 100$ worth of stuff also get it delivered free in 4 days, is awesome. The prices are incredible too.

I just opened up my new Class 5 Curt XD hitch and have not yet installed it so my comments are based on first impressions only. It is very heavy duty - and heavy at 40 lbs. - made of extremely thick metal and outfitted with quality Grade 8 bolts with square necks so they won’t turn when torquing on the nuts to attach the main tube to the side mounting plates. My bolts are plated yellow (which I like) rather than silver as you may have seen in some online photographs. It is substantially beefier than my existing Grade 4 hitch and superior in every way. It’s an impressive piece of hardware. I cannot imagine anyone being disappointed with it on specifications, quality, strength, and general appearance. It’s a beast. What I AM disappointed in is Curt’s packaging and the condition in which the hitch arrived. (This is NOT a reflection on etrailer.com as the hitch arrived in Curt’s original packaging.) The unassembled main tube and the two side mounting plates come bundled together with nothing separating them but shrink wrap. No cardboard, plastic, even paper coming between the metal surfaces - just shrinkwrap probably not even a couple of mils thick. With basically metal-to-metal contact in an oversized-box with the bundle jostling around, it would be a miracle if there were no scratches, gouges, or some type of damage to at least one piece, which is exactly what happened to my hitch. The main hitch tube, on the exterior facing plane, on the driver side where I’ll see it every day, has some gouges on it that go through the powder-coating to bare metal. I can - and will - paint them to prevent rust (and, therefore, have to paint the whole hitch to match). But the gouges will still be noticeable as they go through the thicker, pebbly, powder-coat finish and will undoubtedly still appear as depressions in the surface even once painted. I fully realize this kind of surface damage will almost certainly happen with regular usage of the hitch anyway and that it’s certifiable to demand absolute perfection in anything. But if you are someone who cares about the aesthetics of your equipment and keeping it looking new for as long as possible, it is very disappointing to receive such an expensive and prominent piece of hardware damaged right out of the box and requiring immediate repainting. The plastic parts bag had also ripped open in transit, with nuts, bolts, shims, etc. rattling around in the box. I am dumbfounded that Curt packages such a high-quality piece of equipment so shoddily where such damage is virtually unavoidable. I bought from Curt solely due to their being an American manufacturer and to support American workers so this is doubly discouraging. It’s a trivial complaint in the big scheme of things and not worth demanding a replacement over. Just be aware that unless Curt changes their packaging practices it is very possible you will have the wind taken out of your towing project sails just as I have. Again, this in no way reflects on etrailer. My experience to date with etrailer (website, educational resources, staff reviews, ordering, tracking, email contact, etc.) has been beyond exemplary in every way. They rank as a Top Five online retailer in my opinion, maybe even the best.

Thank you etrailer for the quality products I received early last year. We needed a trailer hitch to install on our Subaru Forester for our move from Gig Harbor, WA to Spokane. We received the hitch hardware including the tow bar and electrical harness. The entire process took 4 hours. The installation process went off without a hitch (bun intended) using detailed videos I found online. Thank you etrailer.

Good price and works as it should.

New GMC AT4 required a new ball mount and this one fit all the requirements for the truck and new multi-pro tailgate. With the AT4, I needed more drop and a longer shank (12" hole) for the tailgate to not hit my trailer jack stand; plus, the multiple drop adjustments will make changing trailers a snap. Great product from Curt and great service from etrailer (as usual).

This is a great ball mount. Fits the Class III hitch on my Explorer perfectly. Works well with my locking anti-rattle pin. However, there is a little noise from the dual pins used for the adjustment. I called etrailer’s customer service to inquire about remedies for this and was told that there is an Allen key adjustment that needs to be tightened to reduce the noise. I have yet to tighten it but other than that, the ball mount has done a great job.

Our problem: back lift gate on our Subaru Ascent SUV would not clear the powered tongue jack on our Casita trailer. Technical person on the phone suggested this this extended ball mount was just the solution and has served us well. Easy to take on and off. Sturdy. No problems for > 9,000 miles of towing this year.

This allowed me to back up my camper easier because it move the distance from hitch to wheels just enough. Very very strong.