Most Popular Square Bars for 2018 Jeep Cherokee

Bought a pair of these to go on 59" rhino rack bars on our Outback Wilderness and am really pleased. I left the bars full width - they are not a head banger on the car - and mounted the Hullavators as far outboard as possible which means the kayaks clear the side of the car and wing mirrors without folding them in. I did have to modify one Hullavator to make the Hobie Lynx fit (36" wide Lynx = 36" max Hullavator width)

The Hullivator was for my wife to give her the option of loading and unloading by herself. It couldn’t be better. She now goes kayaking anytime she wants with little effort and no need for me to help her. Excellent product that’s worth every cent. Was super easy to install too.

They fit well and I feel my Kayak is safe tied down correctly.

After attempting to mount the individual rack pieces using the “burglar proof” button head screws with the pin in the recess and the short hex wrench with the hollowed out end I discovered that no real burglar would want the rack but would rather have the kayak so the first thing I did after spending 10 minutes trying to insert the hex into the button head screws with the pin inside the recess and attempting to turn the bolts and continually being obstructed by the support pieces and the paint interference on the bolt heads with trying to get the wrench into the recess I knew it was going to be a long frustrating process so I threw them away and purchased new button head stainless steel bolts and a 4mm extended handle hex wrench to turn them. Smartest thing I ever did. You not only have to mount the rack initially but then you have to put the kayak on the roof and remount all pieces again to fit your boat. All kayaks are different to one degree or another. Having to move the individual support and retighten them with the boat on the rack is even more difficult to do than the initial mounting with these “burglar proof” bolts and hex wrench and you will be happy you threw them away before you started the entire process. Try it for yourself at first and then go get the alternate ones. Worth the little investment and stainless steel will not rust away when you want to remove the rack system in the future. Once the rack is on your vehicle and kayak in rack the tie downs supplied are very good quality. Make sure you use the recommended tie down locations and directions, two kayak body ties and ties at front and rear. Due to numerous kayak hull designs it would be nice to have each support pod have a horizontal swivel built into it so it readily conforms to the hull shape. The overall quality of the system should be the last rack you will have to purchase. I only had issues with the supplied bolts and hex wrench. I gave this rack system a three star because of the bolts and hex tool and the individual pods not swiveling and I haven't at this point transported the kayak anywhere so I am waiting to see how it handles long trips with wind loads and constant loading and unloading performances.

On my second attempt to find a carrying rack for a Pelican Mustang 100x recreational/fishing kayak, I took great care seeking out a rack that would provide at least six contact points for the boat. The kicker is trying to get good contact points to securely cradle the shape of the Mustang 100x "twin arched multi chine hull" while also cradling the edge of the deck. Delta kayaks calls a similarly shaped hull a "fusion hull". After doing a ton of google advanced searches for images for a racked up Mustang kayak model, I concluded a J-Style carrier seemed to be a secure solution. The etrailer J-Style - Folding carrier has solved the equation, and for a very reasonable price. Paired with a Sherpa Boat Roller, my 5' 4" wife can load and un-load her Mustang 100x kayak on her own for her afternoon paddles on nearby waterways. Now she needs a cockpit cover to keep out the rain, and her carrying system is complete. And etrailer made it an easy return of the first rack system I tried. Thanks etrailer!

We purchased the carrier for our 2011 Sienna to add to our factory installed roof rack. My 15 year old and I manage using it all the time with no issues. We’ve put both our double and our single kayaks up top with no issues. We leave our rack on all the time and have noticed some sun damage to the foam and plastic, so will it last forever in the TX heat? Probably not, but for the price and ease of use, I’d gladly buy another in a few years. Thank you. I reference the YouTube video whenever I forget exactly how the toe downs go, it’s so helpful. Happy customer.

Arrived quickly and was very easy to assemble and attach to the roof of my Jeep. Now that I have the initial setup complete with the proper placement of the entire system, attaching and removing the kayaks will be a breeze. Will definitely make hauling our kayaks much easier and safer.

This product is excellent. I have transported my kayak on these J Hooks several times going 70+ mph down the highway. It never moves. The bolts that come with it are short. If you have a thick roof rack, you will need longer stainless steel bolts. Make sure you you orient the blue straps with the buckle on top so you can pull down to tighten it up.

These kayak J-style racks worked great, AFTER I went to the hardware store and spent $20 on bolts that actually fit my truck rack. It comes with 2-5/8” mounting bolts that aren’t adequate for a heavy truck rack ( mines a Best.Wyle). I had to buy 4” bolts, lock washers, and nuts). I also wish the locking teeth were mitered instead of square. That would make them less prone to breaking and easier to align.

In the meantime, that boy is not to be in this house ever again These kayak carriers are fantastic! They combine with downloaders to make it possible for my wife and I in our advancing years to get our kayaks on top of our car.

Great product and great customer service! Very easy to install, but I highly recommend to watch the installation video first. We used typical black office clips to clip the excess straps down since they came untangled when driving. Also, I recommend to purchase locks for the racks since we are concerned someone may steal them because they are so easy to take on and off.

Great kayak carrier! Highly recommend!

The Rhino Rack cradles, straps and hardware are all good quality and I have no complaints. The only issue I have, and the reason for only a 4 star rating, is the supplied M6 x 40mm Security Head screws are too long for the factory cross bars on my roof rack. When I first installed the cradles if I had tightened the screws all the way, the ends would have dug into the roof and paint, even before I added the weight of the kayak. In checking, I can purchase some M6 x 25mm Security Head screws from Amazon, but frankly part of me feels that for what I’ve already paid for this kit I shouldn’t have to spend another $15 for the correct length screws, plus the package has 20 screws and I only need 8. However, it appears that is exactly what I will have to do. At least they will be stainless steel, rather than the cheaper material the current screws are. Plus I will have extras for when/if the head strips out. I would suggest Rhino Rack consider included in their kit two sets of screws to meet this need. Keep the length they have, Judy add a set of 25mm. I’m still happy with the purchase but not 100%. I do like how the kayak slides easily on the rear felt lined cradles. Plus Rhino Rack includes every tie down strap that you will need, e.g. one each for the bow and stern in addition to two straps intended to secure the kayak directly to the roof rack cross bars. I would highly suggest you get in the habit of using all four straps, you really don’t need to have a gust of wind lifting the nose and tearing the roof rack off your vehicle. Can happen! My brother-in-law lost his roof rack exactly in this manner. So happy yakking and safe travels down the road. By the way I have paired these cradles with the Rhino Rack RTL002 T-Load Hitch Mounted Load Assist and Support Bar for 2” Hitches also purchased from eTrailer. I’ve attached some photos showing my first and second attempts to solve my dilemma. I need to order the replacement screws. First attempt after dark was a large flat washer, then the next day I added some nuts under the large washer. NOTE: Photos may post in reverse order.

This product was very easy to install. I had it installed in about 15 minutes and my kayak on the roof a few minutes later. The only issue I had was one of the tie-down straps was broken (stitching was not complete or something). Other than that, this product was great! The customer service (Carol and Neil) were great also, helping with the strap problem. Thank you again!

Wow is all I can say. I put the Malone cross bars on and then this went up in less than an hour. For an older very petite woman, It went up very easy. Yes, be aware shorties: you need a step stool to be able to get the rack up. I have a folding one that will go in my car. Yep so glad I did this. Thank you Paul B for the help in getting exactly what I needed.

Boxes were in rough shape from shipping but racks were in perfect shape inside. Seems well made and hopefully will be a good replacement for my hullavator which have broken gas shocks.

I bought two of the Malone MegaWing kayak roof rake and I am super happy I did. They are easy to load and with both kayaks up there no problem operating the vehicle. Additionally, the megawing prevent oil canning. I have had other kayak racks, but none of them compare to the Malone MegaWing. And lastly, my set up looks amazing and super sexy with both kayaks up there.

I bought these for my 2015 Jeep Grand Cherokee, for use with 2, small, 10.5' kayaks. They work great. Installation is easy. Most importantly, getting boats up on the roof is much easier than using J-Hook style racks. I do put a rag on the back of the roof of the car to rest the boats on before loading, as advised in the instructions.

Easy loading with a secure tie-down. This is the kayak carrier you should get the first time. I've used flat bars with foam pads - they deform the hull of plastic boats. I've used J-hook style carriers which work well and hold the boat securely without hull deformation, but they increased the windage and are too hard to load on the top of a 4WD pickup. The Malone SeaWings let me slide the kayak on from the rear of the cab while standing in the pickup bed. I use an old bath mat to protect the cab and I can have the boat loaded and tied down in about 5-10 minutes. I also think the load is much more secure than any of the other carriers I've used, especially if the tie-down strap is wrapped around the load bar. The design of the SeaWing puts the main load out on the curved portion of the hull rather than across the flatter area of the bottom and totally avoids deforming the hull. In 90-100 degree heat this is very important to me. Great product. I'll probably get a second pair so I can load two boats on the truck.

I needed a rear-loading rack because the roof rack on my Ford Ranger is up on the topper, and I needed to fit two kayaks side by side. The roof rack bars are 48" wide and the width of the two boats together is about 52". The center clamps of the Malone Seawing fit between the rack towers nicely. The Malone racks have a grippy ribbed rubber surface which is great to keep the boats in place but makes it hard to slide the boats forward. I throw a towel on them to get the boats loaded and then remove it. My Yakima rack has round bars and the Malone racks tilt on the bar when I load the boats. Easy enough to adjust them after the boats are positioned. In this regard the Malone racks would stay flat with square or aero bars. Strapping the boats down is easy. And as always, eTrailer delivery and customer service is fantastic!

This kayak carrier works great with my factory Rav4 roof rack and 10' Tamarack Angler kayak. I did break one tightener knob but probably over-tightened it. And it was replaced for free. I can load and unload the kayak easily and it doesn't budge going down the freeway. I can even drive in and out of the garage with the kayak on the rack for easy storage hanging from the rafters.

Installed this Thule Top Deck Rooftop Kayak Carrier System with tie onto our Thule Roof rack system. Easy to install and this will carry our handmade 17' Wooden Sea Kayak. Very well made.

Incredibly well designed and very convenient to use.

I love the racks and the add-on surfboard carrier. It's so convenient to take my surfboard and other equipment like ladders for my work on and off with this system. It's reassuring to know that they are safely secured on the highway without any additional hassle with ropes or other tie-downs.

4 on canoe rack only because of supplied lower bracket for cross member attachment.

The product is of good construction but probably due to how it fits on my crossbars it needs additional support. The crossbars for my Honda Pilot are wide blade type and these racks seem more appropriate for narrower square type crossbars. Even with the rack fastened very tightly, the rack can twist back and forth. Last year on a trip across Montana the wind was pretty gusty and it caused the front one to pivot quite a bit and we had to pull off and apply a ratcheting strap over the kayak and under the factory rails to ensure it was held tight and wouldn't move again. This year on the same trip we had bad winds but had a roof rack mounted behind these racks giving it support on the tall side. We had to strap it real good to make sure it didn't move. If we hadn't had that additional support behind it and add'l straps we probably would have had more problems. I think if the top metal bracket had a wider channel to fit our crossbars it would be much more stable. The way it is now it just sandwiches 2 metal plates between my crossbar which allows it to pivot under stress.

Excellent product! We have two other sets!

I've been using the product for two summers now and it is perfect for what I'm using it for. My canoe is an Old Town Discovery 133, it's very wide and I initially had trouble fitting it in the brackets with how relatively narrow my Rav4 is, but the instructions that came with them mentioned I could just flip them around. That worked perfectly. I only use the brackets and the tie down straps from the kit to tie the boat to the crossbars, and then use the painter lines I put on the bow and stern of the boat to tie those to the car. That rides on the highway very easily with no shifting. With two people, the load/unload time is around 10 minutes as long as one person knows what they are doing. This kit had exactly what I was looking for, seems built to last, and if I ever need another kit to help tie a canoe to a car then I know I can trust this product to get the job done safely and reliably.

We bought this Kayak rack for my mom to put on her 2016 Jeep Grand Cherokee so her and my dad could haul their kayaks easier. The mounting hardware was a little tricky at first but once we figured it out, it wasn't bad at all. It holds the kayaks in place nicely. Had no issues with them getting loose or moving around. Seems to be built well and they're very happy with it so far.

Decent tie-downs but a bit of work to tie everything down and get the kayak settled, especially with a heavier kayak around 50 pounds and 12 feet long. The rubber pads do their job a little too well in that case!

I purchased a car rack system as well as the kayak carrier and it arrived in only two days! It was easy to put on and fits my 2013 Hyundai Tucson Limited perfectly. I picked up my new kayak the next day and mad it home with no issue what so ever. I am very satisfied with this product.

Jeep wangler 2024 4xe with skyone touch top .Amazing the setup for my fishing kayak 12 feet. Everyone was looking at my setup on the road , and it was secure. Big thx to Kurt w & Paul B to recomand this kayak setup 10/10 www.Etrailer.com

I can't lift my kayak onto my roof rack like I could when I was younger. This looked like a perfect answer to keep me actively using my kayak. It is simple to use, but it does take some strength as you have to lift your kayak onto the loader and must lift the kayak up onto the roof rack as it only loads to just before the top, so keep that in mind. The legs need to be about 6" - 8" longer as mine don't touch the ground at the connectors. I can only reach the ground with them lowered to where they are almost out of the holder. They also touch the Jeep, so I am going to have to carry something to fit between the loader and the Jeep to prevent scratching the door paint. I think if the legs were longer and they fit with both the holder/connectors then I think they might not touch the Jeep. I would have given 5 stars if the legs were long enough. It works with both my moulded J rack and my fold down J rack. It works with both style of kayaks, rounded and straight hulls.

Good quality materials and easy to install - and uninstall. Two changes would give this product 5 stars: Some type of strap holder at the top of the back rack would make it easier to strap down the kayaks and some type of security lock so someone doesn't borrow your new racks while you are out kayaking. One unique thing to remember for the 2017 Toyota RAV4: the back OEM cross bar is about 3" shorter than the front cross bar - this takes some adjustments for the placement of the racks to fit 2 kayaks and still open the rear hatch.

Very good advise by Lauren to purchase this product, happy to have bought it. My tandem kayak twin heron fits without problem. It's easy to install and easy to get the kayak up and down

My biggest worry is losing a kayak off the roof, and these carriers are super secure. Never had a worry. They come with ropes, and I always use them, but I've never seen the ropes get any added tension because their so secure. Also, with my bad back, these are pretty easy to load and unload. I'm 6'2 and have no trouble even though these are pretty high up on the Highlander. I always protect the car with a rug, but rarely does the kayak even touch the rug. You don't have to lift the whole weight of the kayak up to shoulder height, just get one end up to the load assist, and then slide it on, same thing in reverse to unload. Easily mount to the factory roof rack, no need for an expensive system. Took them off for the winter, and am getting ready to remount for a new year of exploring lakes and rivers.

Inno rack pads arrived in a reasonable time and intact/undamaged. They appear to meet all specs and seem well-constructed. Look nice on the rack and will likely work well. My only concerns were: 1) the packaging was riddled with large metal staples . . . over-protected and over-packaged for the product, and a pain to deal with (and not very environmentally friendly). Shipping tape would have been more than adequate. And 2) a very unpleasant odor from the product when opening the package. Took some time to air that out, and had to move the package outside immediately.

I use these consistently without issue.