Most Popular Roof Mount Carrier for 2017 Subaru Legacy

They fit well and I feel my Kayak is safe tied down correctly.

After attempting to mount the individual rack pieces using the “burglar proof” button head screws with the pin in the recess and the short hex wrench with the hollowed out end I discovered that no real burglar would want the rack but would rather have the kayak so the first thing I did after spending 10 minutes trying to insert the hex into the button head screws with the pin inside the recess and attempting to turn the bolts and continually being obstructed by the support pieces and the paint interference on the bolt heads with trying to get the wrench into the recess I knew it was going to be a long frustrating process so I threw them away and purchased new button head stainless steel bolts and a 4mm extended handle hex wrench to turn them. Smartest thing I ever did. You not only have to mount the rack initially but then you have to put the kayak on the roof and remount all pieces again to fit your boat. All kayaks are different to one degree or another. Having to move the individual support and retighten them with the boat on the rack is even more difficult to do than the initial mounting with these “burglar proof” bolts and hex wrench and you will be happy you threw them away before you started the entire process. Try it for yourself at first and then go get the alternate ones. Worth the little investment and stainless steel will not rust away when you want to remove the rack system in the future. Once the rack is on your vehicle and kayak in rack the tie downs supplied are very good quality. Make sure you use the recommended tie down locations and directions, two kayak body ties and ties at front and rear. Due to numerous kayak hull designs it would be nice to have each support pod have a horizontal swivel built into it so it readily conforms to the hull shape. The overall quality of the system should be the last rack you will have to purchase. I only had issues with the supplied bolts and hex wrench. I gave this rack system a three star because of the bolts and hex tool and the individual pods not swiveling and I haven't at this point transported the kayak anywhere so I am waiting to see how it handles long trips with wind loads and constant loading and unloading performances.

Just installed it. So far so good. Ran 2 bike cables side to side with 4 pad locks to secure it for the summer,

Sturdy cradle and easy to install. Difficult to keep tie down strap looped over top of "U" bar while trying to get it over the kayak, keeps slipping down. We made a channel out of foam to keep the strap in place and now it is easy.

Arrived quickly and was very easy to assemble and attach to the roof of my Jeep. Now that I have the initial setup complete with the proper placement of the entire system, attaching and removing the kayaks will be a breeze. Will definitely make hauling our kayaks much easier and safer.

This product is excellent. I have transported my kayak on these J Hooks several times going 70+ mph down the highway. It never moves. The bolts that come with it are short. If you have a thick roof rack, you will need longer stainless steel bolts. Make sure you you orient the blue straps with the buckle on top so you can pull down to tighten it up.

I have not had my kayak on this rack yet but I looks good. I had some struggle with the bolts getting them though the holes properly but it seems fine otherwise. The tale will be told after I mount the kayak.

On my second attempt to find a carrying rack for a Pelican Mustang 100x recreational/fishing kayak, I took great care seeking out a rack that would provide at least six contact points for the boat. The kicker is trying to get good contact points to securely cradle the shape of the Mustang 100x "twin arched multi chine hull" while also cradling the edge of the deck. Delta kayaks calls a similarly shaped hull a "fusion hull". After doing a ton of google advanced searches for images for a racked up Mustang kayak model, I concluded a J-Style carrier seemed to be a secure solution. The etrailer J-Style - Folding carrier has solved the equation, and for a very reasonable price. Paired with a Sherpa Boat Roller, my 5' 4" wife can load and un-load her Mustang 100x kayak on her own for her afternoon paddles on nearby waterways. Now she needs a cockpit cover to keep out the rain, and her carrying system is complete. And etrailer made it an easy return of the first rack system I tried. Thanks etrailer!

These kayak J-style racks worked great, AFTER I went to the hardware store and spent $20 on bolts that actually fit my truck rack. It comes with 2-5/8” mounting bolts that aren’t adequate for a heavy truck rack ( mines a Best.Wyle). I had to buy 4” bolts, lock washers, and nuts). I also wish the locking teeth were mitered instead of square. That would make them less prone to breaking and easier to align.

In the meantime, that boy is not to be in this house ever again These kayak carriers are fantastic! They combine with downloaders to make it possible for my wife and I in our advancing years to get our kayaks on top of our car.

Great product and great customer service! Very easy to install, but I highly recommend to watch the installation video first. We used typical black office clips to clip the excess straps down since they came untangled when driving. Also, I recommend to purchase locks for the racks since we are concerned someone may steal them because they are so easy to take on and off.

Great kayak carrier! Highly recommend!

This is a perfect fit for my needs I found this easy to load by myself. I wasn’t sure about the height of the racks but it turned out to be perfect. I had a full size pickup that was way to tall for this 79 yr old to load, but on the Maverick a with the elevated rack system and the Rhino kayak it works great.

Not the products fault. They were supposed to fit the pre-Thule TracOne rack. Directly asked etrailers support.They don’t fit it. Returned them and grumbled

I acquired a second kayak and needed a system to fit the factory racks on my 2011 Toyota RAV4. Etrailer.com has always had information on what fits and has always had the item needed for the job. I attached the Yakima BigStack to the top with ease, and, with one other person to hold the kayaks while I secured, tied two of them down for a long road trip to Northern Minnesota. The system worked just fine. The only caveat was in the configuration of multiple boats in the instructions. The diagram has two boats on the same side of the posts, however, I found it more secure to put one on either side ( other reviews of this product on different Internet sites have found similar results.) The boats made it through the trip with no shifting.

Where do I start? I've been whitewater kayaking for 22 or so years now. I've always used used either Yakima or Thule products... Until I bought a 2015 Nissan Rogue with a naked roof. The curvature of the roof and large door jams mean that Yakima and Thule can't make racks for them. I went to a place that does custom installs and again because of the curvature of the roof, they couldn't give me a rack. This meant no kayaking which is really bad news. Enter the Rhino rack system. I purchased the feet, the fit kit, the cross bars and a Yakima "big stack" stacker. The first issue I had is the reccomended size for the Nissan Rogue is only 48 inches. Way too small too haul 4-5 (very light) whitewater kayaks. I called etrailer and they were SUPER helpful, told me I can buy the 65 in cross bars and they'll work fine. I held my breath and placed my order. I was nervous leaving my trusted name brands. The order arrived super fast (they told me it would arrive by Friday but it actually arrived on Thursday) and everything was packaged rock solid. I was impressed. I read the instructions and put the rack system on my car. It took about a hour (it was hot and I worked slowly) but the rack system is SUPER SOLID. I love it. Rhino might have a "forever" customer out of me. -The rack system is very stable. I can't move it with my hands by pushing or pulling. -The rubber stripping you put on the top and bottom of the bar is an awesome added feature AND it reduces wind noise. -Adding the fairing reduced wind noise even further. With four boats on the roof you couldn't hear any extra noise. The ONE thing I dislike is that you need to use the supplied Allen wrench to take the rack on and off the car. It's a small complaint, but other systems I've used in the past don't have them. I paid much less for this system than I would have if I purchased one of the aforementioned systems, but I'm really really satisfied with the product. We will see how well it holds up over long-term use, but it looks awesome!

I needed a rear-loading rack because the roof rack on my Ford Ranger is up on the topper, and I needed to fit two kayaks side by side. The roof rack bars are 48" wide and the width of the two boats together is about 52". The center clamps of the Malone Seawing fit between the rack towers nicely. The Malone racks have a grippy ribbed rubber surface which is great to keep the boats in place but makes it hard to slide the boats forward. I throw a towel on them to get the boats loaded and then remove it. My Yakima rack has round bars and the Malone racks tilt on the bar when I load the boats. Easy enough to adjust them after the boats are positioned. In this regard the Malone racks would stay flat with square or aero bars. Strapping the boats down is easy. And as always, eTrailer delivery and customer service is fantastic!

Our kayak club has many members that use this carrier. Since I have back issues, I will use mine on a Malone Eco Light trailer toted from to/from the water using a kayak carrier. Note: Being on a low trailer and so 'accessible', instead of the wingnuts, I bought metric hex nuts to double-nut the bolts to add some security.

Great canoe rack! Fast service!!

As all Thule products the Thule universally mounted canoe carrier is great. It came with all required items for safe and easy canoe transportation. There are two straps with pull to fasten for the canoe down, two tie down ropes for each end with nice pull tight and release mechanisms for the cord as well, along with two straps to fasten to the canoe ends used with the pull to tighten cords. The Chevy traverse cross bar had to have the plastic end caps removed for use with Thule canoe carrier. This was because my canoe took up the entire cross bar width to allow for Thule mounts. It is not a big deal to remove the plastic end caps. They only provide a finished stream lined look. Happy and Safe Canoeing

I bought this rack to replace a Thule Dock Glide for use on my Malone Microsport kayak/canoe trailer. The Dock Glide worked fine on my rooftop wing bars but wouldn't hold my kayak in position on the trailer. Road vibrations and trailer bouncing would cause the kayak to twist no matter how tight my straps. The Swagman Exo Aero mount is an absolutely perfect fit on the Microsport crossbars with the cutout of the mount top portion and a depression in the bottom bar exactly fitting the cross bar (1 1/4") and is rock solid with no chance of shifting position. The Swagman mount is heavily constructed and the rubber strips on the wide bars hold the kayak like a vise. The boat doesn't shift at all no matter how bumpy the road. Great product.

Hi Carol, I emailed my feed back. Out here in the sticks your website couldnt load properly. It a great product. Perfect for this light duty purpose.

Decent tie-downs but a bit of work to tie everything down and get the kayak settled, especially with a heavier kayak around 50 pounds and 12 feet long. The rubber pads do their job a little too well in that case!

I purchased a car rack system as well as the kayak carrier and it arrived in only two days! It was easy to put on and fits my 2013 Hyundai Tucson Limited perfectly. I picked up my new kayak the next day and mad it home with no issue what so ever. I am very satisfied with this product.

Bought a pair of these to go on 59" rhino rack bars on our Outback Wilderness and am really pleased. I left the bars full width - they are not a head banger on the car - and mounted the Hullavators as far outboard as possible which means the kayaks clear the side of the car and wing mirrors without folding them in. I did have to modify one Hullavator to make the Hobie Lynx fit (36" wide Lynx = 36" max Hullavator width)

The Hullivator was for my wife to give her the option of loading and unloading by herself. It couldn’t be better. She now goes kayaking anytime she wants with little effort and no need for me to help her. Excellent product that’s worth every cent. Was super easy to install too.

We bought this Kayak rack for my mom to put on her 2016 Jeep Grand Cherokee so her and my dad could haul their kayaks easier. The mounting hardware was a little tricky at first but once we figured it out, it wasn't bad at all. It holds the kayaks in place nicely. Had no issues with them getting loose or moving around. Seems to be built well and they're very happy with it so far.

High quality materials, great design and the directions to install were excellent. The design of the product is great, I can now carry both of my kayaks on my car. And I have the advantage of carrying them two different ways. I love this pro

Jeep wangler 2024 4xe with skyone touch top .Amazing the setup for my fishing kayak 12 feet. Everyone was looking at my setup on the road , and it was secure. Big thx to Kurt w & Paul B to recomand this kayak setup 10/10 www.Etrailer.com

I can't lift my kayak onto my roof rack like I could when I was younger. This looked like a perfect answer to keep me actively using my kayak. It is simple to use, but it does take some strength as you have to lift your kayak onto the loader and must lift the kayak up onto the roof rack as it only loads to just before the top, so keep that in mind. The legs need to be about 6" - 8" longer as mine don't touch the ground at the connectors. I can only reach the ground with them lowered to where they are almost out of the holder. They also touch the Jeep, so I am going to have to carry something to fit between the loader and the Jeep to prevent scratching the door paint. I think if the legs were longer and they fit with both the holder/connectors then I think they might not touch the Jeep. I would have given 5 stars if the legs were long enough. It works with both my moulded J rack and my fold down J rack. It works with both style of kayaks, rounded and straight hulls.

I had been very happy with etrailer.com in the recent past. On this occasion I ordered this product on 9/6 and requested 2nd day delivery so I could get my wife setup for a weekend outing. My delivery did not come until 9/12, when I checked UPS message it showed "Ground Delivery" not sure if that was correct? When it did show up the box was falling apart. Fortunately everything was intact in the box. I am adding pics of what the box looked like when I received it. No outer box just the original vendors box and it barely held up.. only by tape. Not acceptable on all counts. Your customer service has been great but not to thrilled with shipping! Thank you

Very good advise by Lauren to purchase this product, happy to have bought it. My tandem kayak twin heron fits without problem. It's easy to install and easy to get the kayak up and down

The keys are an issue (wish they were metal), but everything else is great! I go sunrise kayaking only and hate putting straps on with cold hands at 3:30 in the morning. I have a Nissan Pathfinder and was able to put this on with another set of Malone J-hooks so that I can have a second kayak when I go with someone. Once the fear subsides of it possibly falling off, you realize how quick and easy this thing is to use. It takes me 1 minute instead of 9-18 minutes to get my kayak up and secure. I have tested it at 75mph without any jiggling or issues. I sat on this in my shopping cart forever and finally pulled the trigger. If you kayak at least 10 times a year or are going at high speeds for extended periods of time in warm weather, totally worth it. If not, well, there are cheaper options out there.

Unfortunately I did not have the best of luck with this product . I spoke with the company multiple times to ensure this would work with my rack. It did not. This system is made to work ONLY on a roof rack . I have a truck with a rack and a slot in the middle . We had to make different bolts and holders to install this. For using 2 Paddleboards we also had to modify the back of the racks holders to actually touch the boards to hold them in place . After the modifications and many many adjustments we have it working and it does hold great.

Works great and very sturdy no issues. I have it on a seinna van...i also bought a suction cup roller for the back window. Left it on all winterin MA. No issues in car wash either

This combo makes loading and unloading a quick and easy one man job.

Have only taken it out once so far but it was easy to put on and use. Could be easy for someone to steal, I put bike locks on mine to prevent that.

I have four of these. Never had a problem. When you can get them on sale I think these are the best bang for the buck as far as kayak carriers go.

This product was very easy to install. I had it installed in about 15 minutes and my kayak on the roof a few minutes later. The only issue I had was one of the tie-down straps was broken (stitching was not complete or something). Other than that, this product was great! The customer service (Carol and Neil) were great also, helping with the strap problem. Thank you again!

We are pleased with the Rhino Rack kayak rack. We are able to get 2 kayaks on our 2020 Volvo V60, and we ate using Yakima crossbars. The kayaks ride without any drama, and the orientation of the kayaks make it easy to load and unload.