# 1
Draw-Tite Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 8-1/2" Long - 7.5K
Fastest delivery I have ever had. Ordered Wednesday at 5PM, arrived Thursday at 3PM. I'm only a couple hundred miles from Wentzville, but still, excellent. The hitch receiver (2008 Pilot) installed quickly and easily. No need to remove spare or lower muffler. I supported the left end on a large cooler and quickly maneuvered the right side above the tail pipes. The mounting holes were right on target. I had to tap mine to remove rust, but that's easy as well. The wiring harness was also a snapto install. Simple to plug into existing fitting and the wiring box tucked away nicely beneath the trim as advertised. There are options about what to do with the wiring tail and trailer connector. I chose the method shown in the video...leave it rubber-banded in the storage well. Others have run it outside through available holes, but I did not want to leave it exposed to road grime. etrailer's videos were very detailed and shown on my specific vehicle for both the hitch and the wiring harness. Good values as well. If I were Draw-Tite (or Curt) I would include a complementary rubber plug with their logo...cheap advertising.
At 68 yrs old, just single-handedly installed the 50 pound Curt hitch receiver on my 2016 Honda Pilot, using two jack stands and the vehicle's car-jack to position it correctly and hand thread the 6 bolts. Made a bit more room for myself by first lifting the back of the vehicle onto a makeshift ramp consisting of two layered 2x6 board. Also first tried to hand tighten the bolts before placing the hitch under the car and found I had a fair bit of rust to work through with rust blaster and wire brush. Instructions were clear and accurate. One tip, do the center bold on the muffler side first (to be able to slide the unit between the muffler and the frame, then the center bolt on the driver's side second. From there, it is a breeze. Took me an hour to get rid of the rust inside the welded bolts, and then an hour to install the hitch.
# 2
Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 9" Long - 7.5K
The item arrived on time and was exactly what I needed. E Trailer is a great place to fill all my towing needs.
Fastest delivery I have ever had. Ordered Wednesday at 5PM, arrived Thursday at 3PM. I'm only a couple hundred miles from Wentzville, but still, excellent. The hitch receiver (2008 Pilot) installed quickly and easily. No need to remove spare or lower muffler. I supported the left end on a large cooler and quickly maneuvered the right side above the tail pipes. The mounting holes were right on target. I had to tap mine to remove rust, but that's easy as well. The wiring harness was also a snapto install. Simple to plug into existing fitting and the wiring box tucked away nicely beneath the trim as advertised. There are options about what to do with the wiring tail and trailer connector. I chose the method shown in the video...leave it rubber-banded in the storage well. Others have run it outside through available holes, but I did not want to leave it exposed to road grime. etrailer's videos were very detailed and shown on my specific vehicle for both the hitch and the wiring harness. Good values as well. If I were Draw-Tite (or Curt) I would include a complementary rubber plug with their logo...cheap advertising.
# 3
Curt Multipurpose Ball Mount with 2" Receiver for Bike Racks and Cargo Carriers - 7,500 lbs
Everything worked exactly as stated. Very easy to install. The videos are great. Shipping was fast. Very happy!!
I am using the hitch for a car dolly and a bike rack. The fit is a little loose for the bike rackmI'll see it really works when get on the road.
# 4
Curt Towing Starter Kit for 2" Hitches - 2" Ball - 3/4" Rise, 2" Drop - 7.5K
Easy installation, low profile and excellent quality. Exactly what I was looking for in a hitch receiver for our 2021 Pilot.
This was the perfect fit for my Honda Pilot. Installation was very easy; no mistakes were made! The Curt Towing Starter Kit Trailer Hitch Ball Mount was the perfect match for the Trailer Hitch receiver, as it came in a plastic box that fit perfectly in the small stowable compartment in the back of the Honda. Everything stays in the car, tucked away neatly in the plastic box.
# 5
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs
Great instructions, very timely delivery!
very high quality and fits perfectly.
# 6
etrailer 2-3/4" Rise or 4" Drop Ball Mount Kit - 7,500 lbs
Worked great. Was helping a friend move. Worked perfectly, easy to install and having both ball hitches, didn't have to worry about not having the right size for my friends trailer. Really made the move easier.
Thank you for the informative video instructions as well as helpful / honest reviews to research prior to making the purchase. I do not have anything to add that has not been covered in the reviews. Here is a recap of my experience that has been consistent with others. 1. Box was received with the driver side of the hitch pushed out. Only minor scratches which you can not see when installed and it did not impact the installation. Wrapping each end would probably be a good idea as stated in other reviews. 2. Removing 14 years of rust was the hardest part of the install (from the passenger side holes). Total time was approximately 1 hour as others have experienced. I used the bolts from the factory tie hook to work out the rust using 1/2" round wire brush attached to a cordless drill along with a full can of WD-40. 3. Installation of the hitch took about 30 minutes with assistance of a foot stool. 4. Plug-n-play electrical connector took about 10 minutes after watching the video. 5. Perfect fitment, fast delivery, easy website ordering experience and follow-up status notifications, and I can not be more pleased with the cost being under $200 for a DIY project. I required this setup to tow a ~1,000 lb motorcycle trailer with a ~1,000 lb motorcycle next week and my Honda has a 3,500 lb towing capacity. Thank you etrailer.com!
# 7
Curt Tri-Ball Mount - 3 Chrome Balls - 10,000 lbs
definitely solid as a rock
Excellent product! With the three different ball sizes, this tri-ball mount gives you a lot of flexibility. Gone are the days of having several different ball mounts to fit different tongues. High quality construction makes this an excellent investment.
# 8
Curt Class III Ball Mount with 2" Ball - 4" Drop - 2" Rise - 7,500 lbs
2012 Honda Pilot wiring harness 118265. Ordered harness for my Honda Pilot on Monday and received on Thurs!! All parts were in excellent condition on arrival from UPS. I had already read many of the reviews and tips for this harness and that made installation very easy. All the connections went together quickly and easily with no problems. Went to Lowe's and bought 1/4"-20x - 1" stainless bolts and lock nuts as previous installers had said they used. From start to finish took about 1 hr!! I used dielectric grease as stated from installers on connections under bumper exposed to any water. Excellent product and service from etrailer is always superb. I would highly recommend this connector for anybody needing to put 7pole outlet on 2012 Honda Pilot.
This part is sturdy and well built. Exactly as described
# 9
Ball Mount 3/4" Rise or 2" Drop - 12-5/8" Long
2012 Honda Pilot wiring harness 118265. Ordered harness for my Honda Pilot on Monday and received on Thurs!! All parts were in excellent condition on arrival from UPS. I had already read many of the reviews and tips for this harness and that made installation very easy. All the connections went together quickly and easily with no problems. Went to Lowe's and bought 1/4"-20x - 1" stainless bolts and lock nuts as previous installers had said they used. From start to finish took about 1 hr!! I used dielectric grease as stated from installers on connections under bumper exposed to any water. Excellent product and service from etrailer is always superb. I would highly recommend this connector for anybody needing to put 7pole outlet on 2012 Honda Pilot.
This part is sturdy and well built. Exactly as described
# 10
Curt Ball Mount for 2" Hitches - 4" Rise, 6" Drop - 9-1/4" Long - 7,500 lbs
2012 Honda Pilot wiring harness 118265. Ordered harness for my Honda Pilot on Monday and received on Thurs!! All parts were in excellent condition on arrival from UPS. I had already read many of the reviews and tips for this harness and that made installation very easy. All the connections went together quickly and easily with no problems. Went to Lowe's and bought 1/4"-20x - 1" stainless bolts and lock nuts as previous installers had said they used. From start to finish took about 1 hr!! I used dielectric grease as stated from installers on connections under bumper exposed to any water. Excellent product and service from etrailer is always superb. I would highly recommend this connector for anybody needing to put 7pole outlet on 2012 Honda Pilot.
This part is sturdy and well built. Exactly as described
# 11
Curt Class III Ball Mount with 1-7/8" Ball - 2" Drop - 3,500 lbs
2012 Honda Pilot wiring harness 118265. Ordered harness for my Honda Pilot on Monday and received on Thurs!! All parts were in excellent condition on arrival from UPS. I had already read many of the reviews and tips for this harness and that made installation very easy. All the connections went together quickly and easily with no problems. Went to Lowe's and bought 1/4"-20x - 1" stainless bolts and lock nuts as previous installers had said they used. From start to finish took about 1 hr!! I used dielectric grease as stated from installers on connections under bumper exposed to any water. Excellent product and service from etrailer is always superb. I would highly recommend this connector for anybody needing to put 7pole outlet on 2012 Honda Pilot.
This part is sturdy and well built. Exactly as described
# 12
Curt Towing Starter Kit for 2" Hitches - 2" Ball - 2" Rise, 4" Drop - 7.5K
Easy installation, low profile and excellent quality. Exactly what I was looking for in a hitch receiver for our 2021 Pilot.
This was the perfect fit for my Honda Pilot. Installation was very easy; no mistakes were made! The Curt Towing Starter Kit Trailer Hitch Ball Mount was the perfect match for the Trailer Hitch receiver, as it came in a plastic box that fit perfectly in the small stowable compartment in the back of the Honda. Everything stays in the car, tucked away neatly in the plastic box.
# 13
MaxxTow Ball Mount w/ 2" Accessory Receiver - 2" Hitches - 2-1/4" Drop - 5,000 lbs
Heavy duty , very good quality.
# 14
Convert-A-Ball Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 10,000 lbs
Good, very solid ball mount with just the extra rise I needed, 2 3/4", to get level trailer and good clearance for the trailer jack. But excessive shipping charges from etrailer, $[XX] for an $[XX] purchase. Found out to my cost later that [online vendor] would have shipped for free.
As a full-time RVer, e-shopping is very important for us. etrailer was the right place to shop. Right product, delivered on-time for a great price. You beat the local discount RV store by $25 including shipping. At the same time, I had another outfit send me a clearly inferior product to the one they displayed. Said they would e-mail a pre-paid shipping label for the return (didn't) and tried to put the blame on Amazon. Thanks etrailer for a great experience !
# 15
Hidden Hitch Ball Mount - 3/4" Rise, 2" Drop - 15-3/4" Long - 6,000 lbs
Ordered this hitch and it worked perfect for what I needed just bought a teardrop trailer. Couldn't open up the tailgate on my Jeep so I ordered this extended hitch and I brought the ball out past my spare tire and the tailgate opens up now I have no problems. And I looked everywhere couldn't find one of this quality and at this price very reasonable the other ones hundreds of dollars didn't want to spend that much.
This is a huge difference maker for us. I can open the tailgate of our truck with the trailer still attached, and helps minimize any body damage if my backing up is not good.
# 16
Curt Fusion Ball Mount for 2" Hitches - 2" Ball - 2-1/4" Drop - 7,500 lbs
Exactly as described. Well made.
Great deal on this, it was almost $20 more locally. Received it fast, it was packaged very well. This looks really clean on my vehicle and I never have to worry about "did I tighten the ball enough".
# 17
Curt Ball Mount for 2" Hitches - 4" Rise, 6" Drop - 14-1/4" Long - 6,000 lbs
2012 Honda Pilot wiring harness 118265. Ordered harness for my Honda Pilot on Monday and received on Thurs!! All parts were in excellent condition on arrival from UPS. I had already read many of the reviews and tips for this harness and that made installation very easy. All the connections went together quickly and easily with no problems. Went to Lowe's and bought 1/4"-20x - 1" stainless bolts and lock nuts as previous installers had said they used. From start to finish took about 1 hr!! I used dielectric grease as stated from installers on connections under bumper exposed to any water. Excellent product and service from etrailer is always superb. I would highly recommend this connector for anybody needing to put 7pole outlet on 2012 Honda Pilot.
This part is sturdy and well built. Exactly as described
# 18
Convert-A-Ball Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10,000 lbs
Makes for a great hard-core dirt road set up with a 3000 pound trailer, in conjunction with the Curt rocker ball, Towing with an F150 over many miles of washboards, down through washes where the road was washed out, etc. Really makes for a gentler set up on the equipment in the trailer and the truck. Thanks a lot E-trailer!
My usage of your hitch is a bit unusual, I think. I pull a two ton roller with my Ram and I've used your cushioned hitch to smooth out the process. The roller Lunette just dropped over a 2" ball and then banged and jerked on the ball neck. Check out the photos for my adaptation.. I can flip it over and use the 2" ball! Have enclosed some photos. The cushion is holding up very well and it takes a beating!! Thanks
# 19
Curt Heavy Duty Forged Ball Mount for 2" Hitches - 5" Rise - 6" Drop - 17,000 lbs
2012 Honda Pilot wiring harness 118265. Ordered harness for my Honda Pilot on Monday and received on Thurs!! All parts were in excellent condition on arrival from UPS. I had already read many of the reviews and tips for this harness and that made installation very easy. All the connections went together quickly and easily with no problems. Went to Lowe's and bought 1/4"-20x - 1" stainless bolts and lock nuts as previous installers had said they used. From start to finish took about 1 hr!! I used dielectric grease as stated from installers on connections under bumper exposed to any water. Excellent product and service from etrailer is always superb. I would highly recommend this connector for anybody needing to put 7pole outlet on 2012 Honda Pilot.
This part is sturdy and well built. Exactly as described
# 20
Pro Series Tri-Ball Mount for 2" Hitches - 1-7/8", 2", 2-5/16" Balls - Black
EVERTHING WAS EXCELLENT FROM PLACING THE ORDER TO RECEIVING THE PACKAGE AS WELL AS THE FOLLOW UP. WOULD STRONGLY RECOMMEND ETRAILER....
Not only did I get the parts I needed at a great price. They were delivered they day after I ordered them. Great communication from my salesman. I will definitely be a return customer.
What our customers are saying:
"Very broad selection and outstanding service."