Most Popular No Load Assist for 2005 Ford F-150

Great product and great customer service! Very easy to install, but I highly recommend to watch the installation video first. We used typical black office clips to clip the excess straps down since they came untangled when driving. Also, I recommend to purchase locks for the racks since we are concerned someone may steal them because they are so easy to take on and off.

Great kayak carrier! Highly recommend!

Sturdy cradle and easy to install. Difficult to keep tie down strap looped over top of "U" bar while trying to get it over the kayak, keeps slipping down. We made a channel out of foam to keep the strap in place and now it is easy.

Just installed it. So far so good. Ran 2 bike cables side to side with 4 pad locks to secure it for the summer,

Arrived quickly and was very easy to assemble and attach to the roof of my Jeep. Now that I have the initial setup complete with the proper placement of the entire system, attaching and removing the kayaks will be a breeze. Will definitely make hauling our kayaks much easier and safer.

This product is excellent. I have transported my kayak on these J Hooks several times going 70+ mph down the highway. It never moves. The bolts that come with it are short. If you have a thick roof rack, you will need longer stainless steel bolts. Make sure you you orient the blue straps with the buckle on top so you can pull down to tighten it up.

Incredibly easy to install and adjust for a perfect fit. If you’re at least 5’9” you will have no issue hoisting your kayak up onto the rack. The rotation makes this very easy. Absolutely no noise while driving. Secure, tough — I’m very pleased and would recommend this product to anyone!

They fit well and I feel my Kayak is safe tied down correctly.

This is a perfect fit for my needs I found this easy to load by myself. I wasn’t sure about the height of the racks but it turned out to be perfect. I had a full size pickup that was way to tall for this 79 yr old to load, but on the Maverick a with the elevated rack system and the Rhino kayak it works great.

Not the products fault. They were supposed to fit the pre-Thule TracOne rack. Directly asked etrailers support.They don’t fit it. Returned them and grumbled

've previously used the Yakima Kayak Stacker (old style), which worked fine but I always worried the straps would slip off the hook at the top while I was loading boats. They also didn't fold down, so had to be removed after use unless you wanted to look odd and cause a whistle while you drove down the road. They didn't have a universal attachment option, requiring adapters depending on the style and make of your crossbars. More recently I got the Thule "The Stacker", which is a superior solution. You thread the strap through a closed loop at the top, so you don't worry about straps slipping off while you're loading boats. They fold down after use and have a universal style attachment that fits around most styles and makes of crossbars. Good stuff. I really like the straps that come with these, as there is a rubber cover that slips over the metal cam buckle to protect your car's paint while you're tossing the strap over your boats to strap everything in. In order to shuttle our boats for river trips, we needed stackers to fit on both our cars, so it was time for another set. I had never heard of Rhino Rack before, but the lower price than Thile caught my eye, so I read about them and decided to give them a try. The Rhino Rack Nautical Stack used a closed loop at the top, which I liked better than the Yakima or Malone options, and came with the hardware necessary to install them into the C-channel of my Malone aero crossbars, which I wanted to try. I remember that with the Malone stacker, you had to buy the C-channel mount hardware separately. I really like the Rhino Rack Nautical Stack. They are a single post design, unlike the loop style of the Thule "The Stacker". I don't know if this cuts down on vortex drag, but it definitely saves you a couple horizontal inches up where the boats stack. The Rhino Rack Nautical Stack has textured rubber strips on either side of the post, which I believe is intended to cut down on vortex drag, but is also quite helpful in that boats tend to slip much less when you're just leaning them up against the post as you load up before you strap them. That's smart. The Rhino Rack Nautical Stack feels really solid. The mechanism for folding them down and locking them upright is easy to use and feels solid. Installation instructions were good. I tried to install into the C-channels without removing the rubber tubing in my Malone aero crossbars, but couldn't get the little squares to slide into the slots with the rubber tubing in place, so had to cut the tubing, slide the Nautical Stacks into place, then cut down some of the tubing I had removed and replace it in the remaining unfilled crossbar slot. That's not a knock on the Nautical Stack; just a tip in case you're trying to do the same kind of install I did. The one area in which I was less impressed was the tie-down straps that come with this kit. The metal cam buckles have no covering at all, so I'll probably still use my old Yakima and Thule straps instead and use these as backups. But overall, I think these are going to work at least as well, if not better, than the Thule option, and for quite a bit less money.

My wife and I purchased the Rhino Rack Nautic Stack to transport 4 kayaks. We considered similar products by Yakima and Thule, but the acceptable weight limit for the Rhino Rack was there deciding factor. Each of our kayaks weighs 38lbs, and the Rhino Rack was the only item that could handle this load. We were very pleased with etrailer's service and advice. George was extremely helpful. I would highly recommend buying the hood anchors and an extra set of the down straps. The tire down straps are far superior to ratchet-type tie downs that you buy elsewhere - they are strong and SOOO easy to use. I highly recommend the Nautic Stack and etrailer. P.s. we use a bike lock for the Rhino Rack and for our kayaks and they work great for overnight theft protection when we take the kayaks out of town.

These kayak J-style racks worked great, AFTER I went to the hardware store and spent $20 on bolts that actually fit my truck rack. It comes with 2-5/8” mounting bolts that aren’t adequate for a heavy truck rack ( mines a Best.Wyle). I had to buy 4” bolts, lock washers, and nuts). I also wish the locking teeth were mitered instead of square. That would make them less prone to breaking and easier to align.

In the meantime, that boy is not to be in this house ever again These kayak carriers are fantastic! They combine with downloaders to make it possible for my wife and I in our advancing years to get our kayaks on top of our car.

Great canoe rack! Fast service!!

As all Thule products the Thule universally mounted canoe carrier is great. It came with all required items for safe and easy canoe transportation. There are two straps with pull to fasten for the canoe down, two tie down ropes for each end with nice pull tight and release mechanisms for the cord as well, along with two straps to fasten to the canoe ends used with the pull to tighten cords. The Chevy traverse cross bar had to have the plastic end caps removed for use with Thule canoe carrier. This was because my canoe took up the entire cross bar width to allow for Thule mounts. It is not a big deal to remove the plastic end caps. They only provide a finished stream lined look. Happy and Safe Canoeing

I bought this rack to replace a Thule Dock Glide for use on my Malone Microsport kayak/canoe trailer. The Dock Glide worked fine on my rooftop wing bars but wouldn't hold my kayak in position on the trailer. Road vibrations and trailer bouncing would cause the kayak to twist no matter how tight my straps. The Swagman Exo Aero mount is an absolutely perfect fit on the Microsport crossbars with the cutout of the mount top portion and a depression in the bottom bar exactly fitting the cross bar (1 1/4") and is rock solid with no chance of shifting position. The Swagman mount is heavily constructed and the rubber strips on the wide bars hold the kayak like a vise. The boat doesn't shift at all no matter how bumpy the road. Great product.

Hi Carol, I emailed my feed back. Out here in the sticks your website couldnt load properly. It a great product. Perfect for this light duty purpose.

We needed a better way to haul around 3 kayaks and after looking at a number of options, we settled on the Thule Stacker setup. Installation is simple and the stackers provide a sturdy option for hauling multiple kayaks. One of the best features is that they fold down when you don't need to use them. My shopping experience with etrailer was smooth and shipping was prompt.

My wife uses these to carry two small kayaks in the roof of her Subaru. They work great and we very happy with the purchase. She also likes finding her car easier in the parking lots, even with the carriers folded down.

The Rhino Rack cradles, straps and hardware are all good quality and I have no complaints. The only issue I have, and the reason for only a 4 star rating, is the supplied M6 x 40mm Security Head screws are too long for the factory cross bars on my roof rack. When I first installed the cradles if I had tightened the screws all the way, the ends would have dug into the roof and paint, even before I added the weight of the kayak. In checking, I can purchase some M6 x 25mm Security Head screws from Amazon, but frankly part of me feels that for what I’ve already paid for this kit I shouldn’t have to spend another $15 for the correct length screws, plus the package has 20 screws and I only need 8. However, it appears that is exactly what I will have to do. At least they will be stainless steel, rather than the cheaper material the current screws are. Plus I will have extras for when/if the head strips out. I would suggest Rhino Rack consider included in their kit two sets of screws to meet this need. Keep the length they have, Judy add a set of 25mm. I’m still happy with the purchase but not 100%. I do like how the kayak slides easily on the rear felt lined cradles. Plus Rhino Rack includes every tie down strap that you will need, e.g. one each for the bow and stern in addition to two straps intended to secure the kayak directly to the roof rack cross bars. I would highly suggest you get in the habit of using all four straps, you really don’t need to have a gust of wind lifting the nose and tearing the roof rack off your vehicle. Can happen! My brother-in-law lost his roof rack exactly in this manner. So happy yakking and safe travels down the road. By the way I have paired these cradles with the Rhino Rack RTL002 T-Load Hitch Mounted Load Assist and Support Bar for 2” Hitches also purchased from eTrailer. I’ve attached some photos showing my first and second attempts to solve my dilemma. I need to order the replacement screws. First attempt after dark was a large flat washer, then the next day I added some nuts under the large washer. NOTE: Photos may post in reverse order.

This product was very easy to install. I had it installed in about 15 minutes and my kayak on the roof a few minutes later. The only issue I had was one of the tie-down straps was broken (stitching was not complete or something). Other than that, this product was great! The customer service (Carol and Neil) were great also, helping with the strap problem. Thank you again!

Easy loading with a secure tie-down. This is the kayak carrier you should get the first time. I've used flat bars with foam pads - they deform the hull of plastic boats. I've used J-hook style carriers which work well and hold the boat securely without hull deformation, but they increased the windage and are too hard to load on the top of a 4WD pickup. The Malone SeaWings let me slide the kayak on from the rear of the cab while standing in the pickup bed. I use an old bath mat to protect the cab and I can have the boat loaded and tied down in about 5-10 minutes. I also think the load is much more secure than any of the other carriers I've used, especially if the tie-down strap is wrapped around the load bar. The design of the SeaWing puts the main load out on the curved portion of the hull rather than across the flatter area of the bottom and totally avoids deforming the hull. In 90-100 degree heat this is very important to me. Great product. I'll probably get a second pair so I can load two boats on the truck.

I needed a rear-loading rack because the roof rack on my Ford Ranger is up on the topper, and I needed to fit two kayaks side by side. The roof rack bars are 48" wide and the width of the two boats together is about 52". The center clamps of the Malone Seawing fit between the rack towers nicely. The Malone racks have a grippy ribbed rubber surface which is great to keep the boats in place but makes it hard to slide the boats forward. I throw a towel on them to get the boats loaded and then remove it. My Yakima rack has round bars and the Malone racks tilt on the bar when I load the boats. Easy enough to adjust them after the boats are positioned. In this regard the Malone racks would stay flat with square or aero bars. Strapping the boats down is easy. And as always, eTrailer delivery and customer service is fantastic!

These pads worked well on our Yakima RailBar Crossbars- Item #Y00448-0449 that we also bought from etrailer around 2020/2021. Not sure if etrailer carries the exact Yakima Crossbars anymore, but think they have a similar model. Both the pads and crossbars work well to haul our kayak on our 2019 Subaru Forester. etrailer's customer service rocks! We had a lot of questions purchasing both items and they were great to talk to!

works as expected, happy with product

E trailer is a joy to work with. Customer Service is second to none.

The Thule DockGlide Kayak Carrier and the Tie-Downs that came with it are a very functional High Quality Product. Once the DockGlide Carrier was properly positioned on the Cross bars it attached easily and solidly with the associated hardware. The Kayak slides on and off the Carrier very easily and is quite secure once properly tied down. I enjoy Kayaking and the DockGlide Kayak Carrier enables me to get where I want to go.

Thule does make a good product, however these are kind of difficult to set and adjust properly. Once you do get them set, they work flawlessly. It’s the initial set up that is a bit frustrating. Other than that, they work as intended.

Installed it today on my Thule rack. Great product!

Excellent product! We have two other sets!

I've been using the product for two summers now and it is perfect for what I'm using it for. My canoe is an Old Town Discovery 133, it's very wide and I initially had trouble fitting it in the brackets with how relatively narrow my Rav4 is, but the instructions that came with them mentioned I could just flip them around. That worked perfectly. I only use the brackets and the tie down straps from the kit to tie the boat to the crossbars, and then use the painter lines I put on the bow and stern of the boat to tie those to the car. That rides on the highway very easily with no shifting. With two people, the load/unload time is around 10 minutes as long as one person knows what they are doing. This kit had exactly what I was looking for, seems built to last, and if I ever need another kit to help tie a canoe to a car then I know I can trust this product to get the job done safely and reliably.

I acquired a second kayak and needed a system to fit the factory racks on my 2011 Toyota RAV4. Etrailer.com has always had information on what fits and has always had the item needed for the job. I attached the Yakima BigStack to the top with ease, and, with one other person to hold the kayaks while I secured, tied two of them down for a long road trip to Northern Minnesota. The system worked just fine. The only caveat was in the configuration of multiple boats in the instructions. The diagram has two boats on the same side of the posts, however, I found it more secure to put one on either side ( other reviews of this product on different Internet sites have found similar results.) The boats made it through the trip with no shifting.

Where do I start? I've been whitewater kayaking for 22 or so years now. I've always used used either Yakima or Thule products... Until I bought a 2015 Nissan Rogue with a naked roof. The curvature of the roof and large door jams mean that Yakima and Thule can't make racks for them. I went to a place that does custom installs and again because of the curvature of the roof, they couldn't give me a rack. This meant no kayaking which is really bad news. Enter the Rhino rack system. I purchased the feet, the fit kit, the cross bars and a Yakima "big stack" stacker. The first issue I had is the reccomended size for the Nissan Rogue is only 48 inches. Way too small too haul 4-5 (very light) whitewater kayaks. I called etrailer and they were SUPER helpful, told me I can buy the 65 in cross bars and they'll work fine. I held my breath and placed my order. I was nervous leaving my trusted name brands. The order arrived super fast (they told me it would arrive by Friday but it actually arrived on Thursday) and everything was packaged rock solid. I was impressed. I read the instructions and put the rack system on my car. It took about a hour (it was hot and I worked slowly) but the rack system is SUPER SOLID. I love it. Rhino might have a "forever" customer out of me. -The rack system is very stable. I can't move it with my hands by pushing or pulling. -The rubber stripping you put on the top and bottom of the bar is an awesome added feature AND it reduces wind noise. -Adding the fairing reduced wind noise even further. With four boats on the roof you couldn't hear any extra noise. The ONE thing I dislike is that you need to use the supplied Allen wrench to take the rack on and off the car. It's a small complaint, but other systems I've used in the past don't have them. I paid much less for this system than I would have if I purchased one of the aforementioned systems, but I'm really really satisfied with the product. We will see how well it holds up over long-term use, but it looks awesome!

On my second attempt to find a carrying rack for a Pelican Mustang 100x recreational/fishing kayak, I took great care seeking out a rack that would provide at least six contact points for the boat. The kicker is trying to get good contact points to securely cradle the shape of the Mustang 100x "twin arched multi chine hull" while also cradling the edge of the deck. Delta kayaks calls a similarly shaped hull a "fusion hull". After doing a ton of google advanced searches for images for a racked up Mustang kayak model, I concluded a J-Style carrier seemed to be a secure solution. The etrailer J-Style - Folding carrier has solved the equation, and for a very reasonable price. Paired with a Sherpa Boat Roller, my 5' 4" wife can load and un-load her Mustang 100x kayak on her own for her afternoon paddles on nearby waterways. Now she needs a cockpit cover to keep out the rain, and her carrying system is complete. And etrailer made it an easy return of the first rack system I tried. Thanks etrailer!

Straps and hardware seem to be poor quality. Used the rack for the first time this weekend. Worked fine with the first load however the second and third the straps has already started to slip and the hardware no longer tightens done good. Don’t expect there to be much longevity in this product for the price tag

With a little help from youtube, this was one of the easiest things I've ever assembled! LOVE my new SUP rack!!

Very easy to install on roof rack. Just be careful not to lose one of the rubber pieces that help protect your board. They can easily fall off of the rope when tying your board to the rack.

Overall a very high quality option for adding a kayak tie down system to your vehicle. While I was searching for a kayak tie down system this was the only one I found that was a channel mount system that worked with the Adarac line of truck rails. I have the ADARAC Black Matte Pro Series Truck Rack. When I went I install the the nuts that go into the T-channel are way to small and will not allow it to be tightened down. Also the actual mounts them selfs don’t fit the cross beam flush, this could cause the mount to slip to one side or the other of the cross beam. I’m going to looking at ordering the Adarac tie down loops as Adarac doesn’t sell just the channel nuts by them selfs.

The kayak saddle works amazingly well with my set up. I would definitely purchase again or recommend to a friend. I use it often, and it works well even with our strong beach winds.