Most Popular Weld-On for 1990 Dodge Ram Pickup

Very easy to install went right in place of the two support jacks that were broken just removed the existing self tapping screws and one bolt and the job is complete.

Just what I needed great quality and even better price. Fast shipping arived in 5 days all the way across the country.these are great jacks at a great price I would definetly by these from etrailer if I ever need them again.

The gear box is the higher quality metal (aluminum) kind. If you have plastic it will be a big upgrade. The telescoping square connecting shaft that goes between the legs is a noticeably much thicker steel than the OEM one, though it is not painted and does not seem to be galvanized. I wiped it down with a thin coating of WD-40 to prevent rusting. The legs themselves are much the same as the OEM lippart legs that I had but with a few added features. These legs have an easy to remove top plate that is secured with screws (OEM had roll pins that had to be punched out). They also have grease zerks for the gears and the lead screw. There are tapped holes on either side of the leg so that you can orient the zerks for easy access no matter what orientation your rig calls for on installation. There are plugs that go in the unused holes to keep grease from squirting out. This is a huge plus. The main reason that people have problems with landing gear legs is because the lube dries up and the legs seize or become difficult to actuate or the gears get stripped. The only negative thing that I have to say about the legs is, they have a little more play than the OEM ones (inner leg that sleeves into outer leg has a little play). This is not a problem for me because I have stabilizer bars connected to them. But it could bug some people because it would add slightly more shake to a rig with no stabilization. If you want to replace some aging legs that don't work well this is a very good high value way to do it. Knowing what I know now, because etrailer has such great high value parts, I would buy two gear boxes Item # RVLG-RDBOX, two lead legs Item # RVLG-LEGL, two motors Item # M1230 and a second switch # LC138415. This setup would require proper wiring and fusing for the second switch/motor but would give you dual drive and front leveling capabilities.

These worked great and were a good price.

Just as described. Appear to be of very good quality.

Very easy to install went right in place of the two support jacks that were broken just removed the existing self tapping screws and one bolt and the job is complete.

CHEAP! CHEAP! CHEAP! This jack is a wobbly very poorly built piece of junk. Replacing a Ram brand 3500lb with this Ultra Fab 3500lb jack one would think that they would be simular. Not at all. The Ram jack is much more heavy duty. The Ultra Fab should not be rated at any more than 1500lbs. DO NOT BUY THIS FOR A TRAILER WITH MORE THAN A FEW HUNDRED POUNDS OF TONGUE WEIGHT.

I used this on a 1972 Argosy and surprising it fit into the original hole pattern. It works AWESOME--I love it and would highly recommend it to anyone!!

Easy to install and use. Adds stability over factory installed jacks. Quality is good.

these are very well built.

Perfect fit for my Pull behind Motorcycle trailer project. Looks solid and fast shipping! Thanks etrailer!

Click to Enlarge

Excellent product, I can't wait to install it and try it out. So far it seems very strong and capable on Do it what it was design to do.

We just put this on and we love it !!! It is going to make our life a lot easier! !!

Not as good as I had hoped. Jack motor is very slow and seems weak. The twist off cap on the top loses it's o-ring each time I take the cap off to manually wind the jack.

Great, it matched up to where old one was

Great fit

This is replacing a Bulldog jack that's 22 years old and was recently stripped out. It will be a huge improvement. The shipping was fast, and the product showed up very well packaged. I'm looking forward to welding it on this weekend.

I used this on a 1972 Argosy and surprising it fit into the original hole pattern. It works AWESOME--I love it and would highly recommend it to anyone!!

very easy to install, works great.

Product was exactly what I needed. We only had to make one modification to the legs so that we did not have to weld in the new straps. Works perfect. I would love that it instructions would have shown the picture as if you were facing the equipment.

Product was an exact fit for my application only problem I had was key inside gear box fell out but easily fixed once I figured it out.etrailer was spot on helping me find correct jack for my ca.per works great

Seems to be good quality, perfect replacement for the 30+ year old Attwood landing gear that wore out. Installation was fairly quick and easy, with two small issues. First, had to sand down a plastic spacer between gear box and drive bar for bolt to fit. Second, I have to replace the screws that hold motor to gear box, threads on new gear box start 1/4 in back making old screws too short. I was impressed that the jacks have two grease zerks and came well greased.

Click to Enlarge

After one side of my landing gear failed I looked a lot of places for a replacement. etrailer had the full set at a lower price than others had for just the one leg. Reasonable shipping times, everything arrived safely. Best price at least for this item.

Easy to install and use. Adds stability over factory installed jacks. Quality is good.

these are very well built.

Easy to install and use. Adds stability over factory installed jacks. Quality is good.

these are very well built.