What Gauge Wire Does The Curt USCAR Connector C56229 Use?

Question

Question:

What gauge wire does this Curt USCAR 56229 wire harness use? My motorhome 2015 Tiffin has the charge line fused at 30 amp. Thanks, Mark

asked by: Mark

0

Expert Reply:

Hello again Mark. I checked with Curt and the USCAR # C56229 uses 14 gauge wire for every wire but the 12v line. The 12v line is 12 gauge.

expert reply by: Jesse M

0

Answer 1

For your 2002 Ford F-250, the wiring harness you are seeking with both 7-way and 4-way connectors is the Curt T-Connector Vehicle Wiring Harness for Factory Tow Package - 7-Way and 4-Pole Flat Connectors #C55774 or the Reese #74682. Either of these…

view full answer...

Answer 2

I am happy to help you install the Adapter 4-Pole to 7-Pole and 4-Pole part #37185 on the 2003 Subaru Baja. If your trailer does not have brakes and you are using the plug as an adapter to adapt your 4-Way to a 7-way then all you would need to do is…

view full answer...

Answer 3

Hey Richard, to activate the 12 volt accessory circuit of your 7-way you'll need to run 10 gauge wire like part #10-1-1 from the 1:00 pin of the 7-way to the positive post of the battery through a breaker like part #9510. To activate the Ford…

view full answer...

Answer 4

The standard wire gauge for USCAR 7-way 12 volt accessory circuits is 12 gauge. You won't find a setup that uses 8 gauge unless someone custom wired it like that.

view full answer...

Answer 5

Great question, Kevin. The Onboard Scale system on your 2024 Ford F-350 Super Duty works by essentially measuring how low the bed is sitting and it gives an estimated weight based off of that. If you added a suspension enhancement then that would…

view full answer...

Answer 6

Hey Willyd, it looks like you have a 7-way round connector which is a bit more rare and for that we only have a 7-way to 4-way adapter like the part #47405. Does your trailer with a 5-way actually use the 5th circuit? If so what is it for?

view full answer...

Answer 7

Using a junction box makes installing new 7-way wiring much easier. Often times, people will run the wires from a 7-way such as yours to a junction box like part #38656. From there, they will run the standard wire colors to the trailer lights, brakes…

view full answer...

Answer 8

If your Ford E-350 has a 7-way on it currently that uses a harness that looks like what you see in the picture I attached the part #C57101 is going to work. Nearly all 7-way harnesses use this same style of connector so there is a good chance this…

view full answer...

Answer 9

Any time your vehicle is placed in reverse, whether you are towing or not, the alarm will sound on the Curt Trailer Connector Adapter with Backup Alarm item #C57102. To have the same connector without the beeping sound you will want the Curt Trailer…

view full answer...

Answer 10

The Westin grille guard #57-2365 does not having mounting tabs for additional lights. The holes that would normally be there to add additional lights are being used to hold the mesh part of the HDX. To add additional lights you can use the universal…

view full answer...

Answer 11

The punch plate refers to the mesh looking section at the top of the grille guard. I attached a picture with it pointed out.

view full answer...

Answer 12

The Curt Universal Wiring Harness for Vehicle-End Trailer Connectors #C56229 is what is referred to as a US Car Connector. It will match pin location functions so your lights will match up. The colors on this harness may be slightly different as you…

view full answer...

What Gauge Wire Does The Curt USCAR Connector C56229 Use?

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching