Is a Replacement Gear Housing Available for the Fulton F2 Swing-Up, Wide-Track Trailer Jack?

Question

Question:

Do you have the gear housing for a F 2 1600 lb. 1413040134 ?

asked by: Sheldon D

0

Expert Reply:

No, Sheldon I am sorry we do not. Additionally, I checked with Fulton and they do not offer what is labeled part number 9 on the exploded diagram listed below. If you need to replace this part you will most likely have to purchase a new Fulton F2 Swing-Up, Wide-Track Trailer Jack item # F1413040134.

expert reply by: Jerred H

0

Fulton Jack Diagram
(click to enlarge)

Answer 1

For a jack that is similar to the Round Swivel Marine Jack #MJ-1206B I recommend the Pro Series Round, Snap-Ring Swivel Jack #PS1400300303. This jack has a footplate instead of a wheel and has a 2,000 lb lift capacity. This features a bolt on…

view full answer...

Answer 2

The Pro Series Swivel Jack #PS1400300303 that you referenced should fit fine in your application. In the picture of the jack that I have provided has the measurements indicated. From the center of the mounting bracket to the foot plate is 11 inches.…

view full answer...

Answer 3

I spoke to my contact at Dutton-Lainson and was able to confirm that the Pull Pin, Easy Swivel Trailer Jack with 6" Wheel part #DL22457 for 10" lift or part #DL22560 for 12" lift is a direct replacement for the jack you have on your…

view full answer...

Answer 4

The Fulton F2 Swing-Up Trailer Jack #F1413040134 (as well as other F2 jacks) has that plastic piece that as you referenced is #9 in the exploded diagram. I reached out to my tech contact at Fulton and unfortunately that is not a replaceable part. You…

view full answer...

Answer 5

The current version of the Dutton Lainson Trailer jack you have now is the part #DL22457 which is a side mount side crank bolt on trailer jack with a 1,000 lb capacity.

view full answer...

Answer 6

There are some Dutton-Lainson trailer jacks that are made in the USA as well as a few that are not. Any jacks that we carry that are made in the USA have that as part of the description to help set them apart. Currently we have the following options:…

view full answer...

Answer 7

I took a look at the installation instructions for the Fulton Bolt-Thru Swivel Marine Jack part #FXP15W and there isn't any sort of torque spec for the center bolt but what is stated is that you will need to tighten the lockout until there is…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Hey Rebecca! Information is limited and isn't finalized yet from Trailer Valet since the #TV83FR is still a preorder. However, I was able to find that the full height of the jack when it is retracted is 33" from the wheels to the top. I also…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Is a Replacement Gear Housing Available for the Fulton F2 Swing-Up, Wide-Track Trailer Jack?

Product Page this Question was Asked From

Continue Researching