Recommended Stabilizer Supports For Equipment Trailer That Lifts Back Of Truck Off The Ground
Question:
I have an 14,000 lb Iron Bull Equipment trailer that I tow with a 2017 F250, I have the Large ramps with the trailer. I tow a Kubota M7060 Tractor... about 6,500 lbs total weight. When I load the tractor it will lift the rear of my truck right off the ground... I am looking for a USA made jack... looking at this Jack: Dutton-Lainson Trailer Jack - DL22685 I see the lift capacity is 2,000lb. What is the holding capacity. I would lower this jack to within 2inch of the ground before loading and just use it to stabilize until loaded then fold it up out of the way. I have about 22inch of horizontal clearance to work with... What is the Holding Capacity of this jack?
asked by: Bruce M
Expert Reply:
Dutton-Lainson does not give a separate holding capacity for their Pipe Mount Jack # DL22685. The Fulton Drop-Leg Stabilizer Jack # FSJ1-SJ2 is one of the popular options for your type of situation. Each of these have a 3,000lb capacity so with one on each side that will likely be enough capacity for your Kubota M7060 Tractor since not all of the weight is going to be on just the stabilizers.
Products Referenced in This Question
Fulton Drop-Leg Stabilizer Jack with Mounting Channel - Weld-On - 28" Leg - 13" Bracket -
- Camper Jacks
- Pop Up Camper
- Teardrop Camper
- Travel Trailer
- Side-Mount Jacks
- Stabilizer Jacks
- Steel
- 2001 - 3000 lbs
- Manual Jack
- Weld-On
- 1 Jack
- Fulton
more information >
Product Page this Question was Asked From
Pipe Mount Swivel Style Trailer Jack with Foot - Sidewind - 10" Travel - 2,000 lbs.
- Trailer Jack
- Enclosed Trailer
- Utility Trailer
- Side-Mount Jacks
- Swivel Jacks
- Standard Grade
- 1001 - 2000 lbs
- Manual Jack
- 10 Inch Lift
- Weld-On
- With Rectangle Foot
- Dutton-Lainson
more information >
Continue Researching
- Shop: Fulton Square Drop Leg for Stabilizer Jack, 29" Long
- Video: Ultimate Overview of the Fulton Drop-Leg Stabilizer Jack with Mounting Channel
- Shop: Fulton Drop-Leg Stabilizer Jack with Mounting Channel - Weld-On - 28" Leg - 13" Bracket -
- Video: Comprehensive Review: Fulton Square Drop Leg for Stabilizer Jack, 29" Long
- Search Results: rear stabilizer jacks
- Shop: Square A-Frame Jack w/ Footplate - Drop Leg - Sidewind - 28-3/4" Lift - 3,000 lbs
- Shop: Phoenix Electric Trailer Jack with Remote - A-Frame - 26" Lift - 5,500 lbs
- Search Results: fulton drop leg
- Search Results: drop jack
- Shop: Square Direct Weld Jack w/ Footplate - Drop Leg - Sidewind - 28-7/8" Lift - 7,000 lbs
- Shop: Replacement Drop Leg for etrailer and Ram Square Direct Weld Jacks - 3K
- Shop: TowSmart Boomerang Hitch Pin w/ Clip for 1-1/4" and 2" Hitch Receivers
- Search Results: jacks
- Video: All You Need to Know About the Loadstar ST205/75D15 Bias Trailer Tire with 15" White Wheel
- Search Results: drop leg stabilizer
- Search Results: wheel chock
- Search Results: tire mount
- Video: Review of the Replacement Jack Leg for Fisher Snow Plow
- Video: Replacement Drop Leg for etrailer and Ram Square Direct Weld Jacks Review
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: Where Do the Wires on the Universal Install Kit for Trailer Brake Controllers Get Installed?
- Video: etrailer Trailer Jack TJD-7000-FT Review
- Video: An In-Depth Look at the Quick Splices
- Shop: Brake Controller
- Shop: Trailer Hitch
- Shop: Trailer Wiring
- Q&A: Measurement of Drop Leg of the Fulton Drop-Leg Stabilizer Jack with Mounting Channel
- Q&A: What is Diameter Of Mounting Pipe on Pro Series Round Pipe-Mount Swivel Jack # PS1401460303
- Q&A: What Size is the Tubing on the Fulton Square Drop Leg for Stabilizer Jack
- Q&A: Recommended Support Jacks for Rear of Tandem Axle Dump Trailer
on Trailer Jack
Bruce M.
4/18/2024
Is the Fulton jack also made in the USA? Thanks in advance!