Mounting Hardware Needed To Install Curt QuickPin No Latch A-Frame Trailer Coupler 25474 # C84DR
Updated 10/31/2023 | Published 10/26/2023
Question:
Hello: Question about Curt EZ latch coupler 25474....for 50 degree mounting. An installer is asking me the dimensions of the bolts needed......especially the length of the bolts. Can you tell me complete specs of the bolts, etc. Thanks.
asked by: Steve S
Expert Reply:
The Curt QuickPin No Latch A-Frame Trailer Coupler 25474 # C84DR will require grade 5 hardware. It is recommended to use six 1/2" bolts, six 1/2" lock nuts and twelve 1/2" washers. This can obviously change depending on your exact frame dimensions. I have linked the installation instructions at the bottom of the page which you can show the installer as well.
Product Page this Question was Asked From
Curt QuickPin No Latch A-Frame Trailer Coupler w/ Jack Hole - 50 Degree - 2-5/16" Ball - 14K
- A-Frame Trailer Coupler
- Standard Coupler
- 50-Degree Frame
- Bolt-On
- Weld-On
- 14000 lbs GTW
- 2-5/16 Inch Ball Coupler
- No Latch
- 2-1/4 Inch Hole
- Standard Grade
- CURT
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Curt QuickPin No Latch A-Frame Trailer Coupler w/ Jack Hole - 50 Degree - 2-5/16" Ball - 14K
- Shop: Trailer Idler Hub Assembly for 3,500-lb Axles - 6 on 5-1/2 - Pre-Greased
- Shop: Curt Hitch Lock - 2", 2-1/2", and 3" Hitches - Chrome
- Search Results: safety chains
- Search Results: trailer hitch
- Search Results: accessories and parts
- Search Results: wheel nuts
- Search Results: trailer leaf springs
- Search Results: trailer coupler
- Search Results: trailer hub
- Shop: A-Frame Trailer Coupler - Underslung - Thumb Latch - Black - 2-5/16" Ball - Weld On - 14K
- Video: Detailed Breakdown of the Curt QuickPin No Latch A-Frame Trailer Coupler w/ Jack Hole
- Shop: A-Frame Trailer Coupler - Thumb Latch - Black - 2-5/16" Ball - Weld On - 14,000 lbs
- Q&A: Locking Pin Recommendation for the Curt QuickPin No Latch A-Frame Trailer Coupler
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Q&A: What Is The Spring Rate Of SuperSprings SuperCoils SSC-50 For 2019 Ram 1500 Classic?
- Q&A: How to Measure the Angle of Trailer A Frame To Determine if a 50 Degree A Frame Coupler will Fit
- Q&A: Replacing A-Frame Surge Brake Actuator On 1966 Scotchman Camper
- Q&A: How Wide are A-Frame Trailer Couplers CA5400 and CA5100B
- Q&A: Replacement For 8,000 lb A-Frame Trailer Coupler With 2-5/16 Inch Hitch Ball
- Q&A: Hardware Kit For A Demco Cast Head Coupler.
- Article: Trailer Wiring Diagrams
- Article: Trailer Maintenance Schedule
- Article: Wiring Trailer Lights with a 4-Way Plug (It's Easier Than You Think)
- Article: Can You Flat Tow a Jeep Compass?
- Article: Trailer Lighting Requirements
- Article: How to Raise Your Travel Trailer Height