How Are Shackle Straps Supposed to Be Positioned When The Trailer Is Loaded?
Updated 10/23/2023 | Published 10/20/2023
Question:
I am replacing my leaf springs on my toyhauler. The new springs are longer for more clearance between the tires and have more arc and leaves. The non equalizer sides will need a hole spaced further out. How do I figure how much further to put the hole? How are the equalizer straps supposed to be positioned when unloaded or loaded?
asked by: Robert
Expert Reply:
As far as repositioning the hole in your hanger, that will depend on how much longer the new leaf springs are versus the stock spring. Say for example the new springs are 1" longer than stock when measured center eye to center eye across. I would say split that distance in half. So moving the hole out 1/2" will get you to where the shackles should be at an appropriate angle. Adding a bit more arc and leaves will add to your ride height.
As far as the shackle strap position, there is not really a "set in stone" angle for a shackle strap. They should be around 45 degrees or so when the trailer is loaded. I have attached a picture below that will show an example of the proper angle when loaded. You basically just want the shackle strap to be angled towards the axle, so that as the leaf spring flexes, it will have somewhere to go. So if you are not at exactly 45 degrees, the suspension will still articulate correctly, as long as the shackle stays angled towards the axle.
(click to enlarge)
Product Page this Question was Asked From
Front/Center/Rear Hanger for Double-Eye Springs - 3-1/4" Tall - 9/16" Bolt Hole
- Trailer Suspension Parts
- Hangers
- Boat Trailer
- Camper
- Car Hauler
- Snowmobile Trailer
- Utility Trailer
- Double Eye Springs
- 9/16 Inch Diameter
- 3-1/4 Inch Tall
- Single Axle
- Tandem Axle
- Triple Axle
- etrailer
more information >
Continue Researching
- Search Results: trailer leaf springs
- Search Results: trailer suspension parts
- Search Results: boat trailer parts
- Search Results: tandem axle trailer equalizer kit
- Shop: Dexter Heavy-Duty Suspension Kit for Tandem-Axle Trailers - 1-3/4" Wide Double Eye Springs
- Search Results: dexter trailer leaf springs
- Search Results: accessories and parts
- Search Results: dexter trailer springs over~under conversion kit
- Video: Review of the Suspension Kit for Tandem-Axle Trailers
- Q&A: Hanger Kit to Use with Leaf Spring # SP-216275
- Q&A: Typical Hanger Spacings for Tandem Axle Trailer with 3,500 lb Axles
- Shop: Suspension Kit for Tandem-Axle Trailers - 1-3/4" Wide Double Eye Springs - 2-1/4" Links
- Shop: 4-Leaf Double-Eye Spring for 3,500-lb Trailer Axles - 25-1/4" Long - EMCO
- Shop: U-Bolt Kit for Mounting 3,500-lb, Round Trailer Axles - 5-1/2" Long U-Bolts
- Shop: 4-Leaf Double-Eye Spring for 3,500-lb Trailer Axles - 25-1/4" Long
- Shop: CE Smith U-Bolt Kit for Mounting 3,500-lb, Round Trailer Axles - 5-1/2" Long U-Bolts - Zinc
- Shop: Dexter Tandem-Axle Trailer Hanger Kit for 2" Slipper Springs - 38" Axle Spacing
- Video: What to Know About the Dexter Heavy-Duty Suspension Kit for Tandem-Axle Trailers
- Video: Review of CE Smith Trailer Suspension Parts - Shackle Bolts - CES25QR
- Video: What to Know About the etrailer Rust-Resistant 4-Leaf Double Eye Spring for 3.5K Trailer Axles
- Video: Checking Out the etrailer Rust-Resistant 4-Leaf Double Eye Spring for 3.5K Trailer Axles
- Q&A: How Do I Figure Out What Equalizer Upgrade Works For My Trailer?
- Q&A: Angle Of Shackles On Trailer Appear Wrong When Installing Leaf Springs
- Q&A: How to Determine the Distance for Mounting Trailer Spring Hangers on a Single Axle Trailer
- Article: How to Tell the Weight Rating of a Trailer Axle
- Video: 4-Leaf Double-Eye Spring for 4,000-lb Trailer Axles Spec Review
- Video: Comprehensive Review: Dexter Heavy-Duty Suspension Kit for Tandem-Axle Trailers
- Article: Double-Eye Trailer Suspension System Review
- Q&A: How To Determine Where Leaf Spring Hangers Should Be Placed
- Article: How to Raise Your Travel Trailer Height
on Trailer Suspension Parts
