How to Replace the Red Knob for the Yakima FrontLoader Bike Carrier

Question

Question:

There seems to be a keeper washer below the nut and washer that hold the knob on. Is there a trick to removing it?

asked by: Michael K

0

Expert Reply:

There shouldn't be another washer on the Replacement Red Knob for Yakima Frontloader Fork Mount Bike Carrier # 8880226. That appears to be part of the internal threads on the red knob itself. To replace this piece you'll just have to replace the brass nut and bolt that hold this to the rack and you'll be all set.

expert reply by: Bryce D

0

Red Knob for Yakima FrontLoader
(click to enlarge)

Answer 1

To replace the knob on your Yakima FrontLoader #Y02103 you will remove the brass nut and bolt that keep the knob secure. If your FrontLoader was made after 2016 you need the #8880766. If it was made before 2016 you will need the #8880226 instead.

view full answer...

Answer 2

There are a few ways to tell if you have a pre-2016 or post-2016 Yakima FrontLoader Wheel Mount Bike Carrier part #Y02103. The best way to tell is to look for the date code sticker which is usually located near the front wheel holder. The easiest way…

view full answer...

Answer 3

Is it possible your FrontLoader was built after 2016 which would mean you'd need the knob part #8880766 which has a different nut in it and would explain why the older knob #8880266 isn't threading correctly.

view full answer...

Answer 4

Hey James, so the difference between the two knobs is going to be when the rack you have was made. If your Frontloader was made after 2016 you need the part #8880766 or if before you'd need part #8880226.

view full answer...

Answer 5

Yes, you will remove the brass nut and bolt and the red knob will come off. You should note that the #8880226 does not come with a new nut (just a washer), so be sure not to lose your current one.

view full answer...

Answer 6

You will want part #8880766 , which includes the brass nut for the Yakima FrontLoader bike rack made after 2016. This includes the brass nut that secures the knob to the bike rack. If you have one made prior to 2016, you'll want part #8880226…

view full answer...

Answer 7

It does sound like you may have overtightened or there is something wrong with the threading on your knob on your Yakima Frontloader. Replacing the knob should solve your problem. If you have Yakima FrontLoader bike rack made after 2016 you will need…

view full answer...

Answer 8

The Yakima Replacement Hitch Hardware for Yakima HoldUp Bike Racks #8890260 that you referenced is Metric.

view full answer...

Answer 9

I spoke with Yakima about removing the SpeedKnob on the Yakima RidgeBack Bike Rack and she stated that you need to just use more force since the threads are likely stripped. The other option which would not require excessive force would be to take…

view full answer...

Answer 10

The dynamic weight capacity of the RetraxPRO XR Hard Tonneau Cover #RTT-80851 is 500 lbs so it would easily handle the 600 lb weight you mentioned since that would be a "static" weight meaning it's not weight on the rack when on the…

view full answer...

Answer 11

Even if there was a third bar option for the Retrax #RTT-80232 you are limited to 500 lbs evenly distributed. There wouldn't be a safe way to increase it. But if you are at 450 lbs and not 500 you'd be totally fine with it.

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

How to Replace the Red Knob for the Yakima FrontLoader Bike Carrier

Product Page this Question was Asked From

Continue Researching