Pre-Greased Trailer Hub for Floe Pro 100 Snowmobile Trailer

Question

Question:

Hi I have a floe pro 100 2 place snowmobile trailer. Looking for prepacked hub assembly. 5- 4 1/2 bolt pattern.

asked by: Jared

0

Expert Reply:

From previous customers who have the same Floe Pro 100 trailer we have determined that the correct replacement hub would be for a 2k axle like with the part # AKIHUB-545-2-1K which is pre-greased.

expert reply by: Jameson C

0

Answer 1

I'm assuming you mean a U-bolt kit to mount your axle to the leaf springs on your FLOE Pro 100 snowmobile trailer. The correct kit will depend on your capacity/axle diameter. If you have a 2k axle that uses hubs like the #34822545BX you were…

view full answer...

Answer 2

We don't currently carry any torsion axles. You also have a unique frame width, so I have an alternative solution for you. I recommend the Timbren Axle-Less Trailer Suspension System with Hubs - 5 on 4-1/2 - Regular Tires - 2,000 lbs #A20RS545 or…

view full answer...

Answer 3

We do have a spindle that fits that description with part #TRU44FR. This uses two #L44649 (1.063" inner diameter) bearings and a #10-9 (1.50" inner diameter) grease seal.

view full answer...

Answer 4

Luckily, FLOE International is still around. I was able to find that your 10 foot tilt single axle snowmobile trailer used an L44649 inner and outer wheel bearing. Your snowmobile trailer was equipped from the factory with idler hubs that had a 5 on…

view full answer...

Answer 5

Thank you for the photo of your vintage utility trailer's spindle. The simplest and surest way to identify a compatible trailer hub is to identify the inner and outer bearings and the grease seal it uses. Matching up those components along with…

view full answer...

Answer 6

I may have another option for you, but the Dexter Trailer Idler Axle Beam with EZ-Lube Spindles - 72" Long - 2,200 lbs #T20BTR-EZ-7258 you were looking at uses inner and outer bearing #L44649 which is used for 2000lb hubs like the Dexter Trailer…

view full answer...

Answer 7

The bearing part #L44649 has an inner diameter of 1.063 and is typically used in 3,500 lb axle hubs and the #L44643 has an inner diameter of 1 inch and is typically used on 2,000 lb axle hubs. If you can get me more info on your trailer like axle…

view full answer...

Answer 8

Are you sure the diameter of the spindle is 1.25 inches where both bearings ride? That's not typical for a 2,000 lb axle but if instead the diameter is 1.06 inch then you could use the hub part #AKIHUB-545-2-2K which has the 5 on 4-1/2 bolt…

view full answer...

Answer 9

A 2000 lb axle uses a straight spindle, with both the inner and outer bearing being the same size. The hubs needed will depend on the number of lugs your current hubs have and which inner/outer wheel bearings are used. I'll give you a run-down on…

view full answer...

Answer 10

I have a solution for you. However, you are going to need a little more information to make sure you receive the correct hubs to replace you current oil bath hubs. You will need the bearing numbers of your current hub to match with the replacement…

view full answer...

Answer 11

Yes, the Dexter Trailer Idler Hub Assembly part #8-91-05UC1 will work with the bearing part #L44643 and the race part #L44610. They both have a 1.980" outer diameter which is why they are compatible with the above trailer hub. As long as your…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Pre-Greased Trailer Hub for Floe Pro 100 Snowmobile Trailer

Product Page this Question was Asked From

Continue Researching