Replacement Switch Solution For A Superwinch T1500 Winch

Question

Question:

I have a superwinch t1500 that works great. This past weekend the Switch broke. Do you have anything I can replace it with? Thanks

asked by: David M

0

Expert Reply:

Sure thing!

You can use the:

-Replacement Momentary Rocker Switch for Bulldog Winch 4-Switch Panel w/ Lighted Breakers # BDW20261 with your Superwinch T1500 Winch.

This switch measures 115/16" wide x 1-15/16" high x 1-15/16" deep and is water and weather resistant to IP68 specifications.

expert reply by: Bryce D

0

Answer 1

You are correct that is a 3,500 lb axle. If you want a bearing kit the #BK2-100 you looked at is the right one. This comes with a #L44649 outer and #L68149 inner bearing along with a #58846 (10-19) grease seal. If you want a replacement idler hub you…

view full answer...

Answer 2

It took a little while to get your information from Dexter. Your axle is a #13 Torflex Axle which is rated for a capacity of 8,000 lbs. We don't have an 8,000 lb capacity replacement, but we do have 7,000 lb capacity Axle-less Systems you may…

view full answer...

Answer 3

Thanks for the information! Based on the information you provided my contact at Dexter was able to confirm that you have a 3500lb axle with a 94.5" hub face to hub face measurement and an 81" spring center to spring center measurement. For…

view full answer...

Answer 4

We do not carry the replacement axle for your P12 7K Axle. We do however have the brake assemblies and bearing kit or hub/drum assemblies to assist based on what I can find online for a 7K Dexter axle. You will most likely want the Bearing Kit,…

view full answer...

Answer 5

I'm not quite sure what you mean by the "heart", however for your Ventline VD0434 we have the replacement screen frame #BVA0444-32, the replacement lid #BVD0449-A01, and the replacement ceiling garnish #VA0445-28 all available for…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 10

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

The BTR and BT8 denotations refer to the spindle, not the trailer hub. The difference between a BTR and BT8 spindle is that the BTR spindle uses a 1.063" diameter L44649 bearing and the BT8 spindle uses a 0.99" diameter L44643 bearing. In…

view full answer...

Replacement Switch Solution For A Superwinch T1500 Winch

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching