Correct Replacement Operator Mechanism for MaxxAir MaxxFan 7500K Roof Vent

Question

Question:

Howdy. I have an older [from 2016] Maxxfan 7500K with a bad Operator Mechanism. Ive read that a new Lift Arm is also needed due to a pattern change from square to hex on the end of that arm. Hoping that you can guide me in the right direction of needing the arm or not. This will save me from tearing it apart twice. Thanks for your help.

asked by: Austin S

1

Helpful Expert Reply:

I checked the repair parts list for a MaxxAir 7500K Roof Vent and the Replacement Operator Mechanism for MaxxAir MaxxFan Plus or MaxxFan Deluxe Roof Vents part # MA10-20281K-1AF is listed as a fit without any exclusions such as date of manufacture so you can be confident that this item will fit without any other parts needed.

expert reply by: Conner L

1

John S.

7/13/2024

this is not the case, my lift rod is square and the above metion part is hex

Reply

Kevin C.

7/15/2024

@JohnS What's the model number of your vent?

Reply

Answer 1

The two most likely causes of a MaxxAir vent fan lid not opening or closing are either going to be a lift motor or operator failure. I recommend removing the motor and applying power directly to this to see if the shaft turns. If not, you know the…

view full answer...

Answer 2

If the lid no longer opens or closes even when using the manual knob then that means the operator mechanism is bad which is rather common to have to replace. The part you'll need for this is the Replacement Operator Mechanism for MaxxAir MaxxFan…

view full answer...

Answer 3

The correct replacement circuit board for your MaxxFan 7000k unit is the part #MA10A21275K that you referenced. The different letter in the part number is just a slight change they made but does not affect application.

view full answer...

Answer 4

Sounds like you have a damaged or worn out roof vent operator and need to replace it with the part #MA10-20281K-1AF since you said the motor doesn't want to fully open or close the lid and it's difficult to turn by hand.

view full answer...

Answer 5

The MaxxFan Deluxe Roof Vent, #MA00-07500K probably has a faulty operator mechanism or lift motor. The correct replacement part number for Replacement Operator Mechanism for MaxxAir MaxxFan, is #MA10-20281K-1AF. The Replacement Lift Motor for Maxx…

view full answer...

Answer 6

It sounds like you could be referring to either Replacement Operator Mechanism part #MA10-20281K-1AF or Replacement Lift Arm part #MA10-20222KS which are both fits for a MaxxAir 7000K Roof Vent Fan. If you need a different part let me know but these…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Hi Eric; the correct capture plate for the PullRite SuperGlide 5th Wheel Hitch #PUL83RR depends on the pin box on your 5th wheel. The manufacturer can identify it if you get the serial number off of the pin box sticker or you can measure the bolt…

view full answer...

Answer 10

The best replacement option we offer for a Atwood GC10A-4E Water Heater is tankless, the Furrion RV Tankless Water Heater part #FR68SR. It won't be a direct replacement but still pretty easy nonetheless as they are very similar. That said, you…

view full answer...

Answer 11

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 12

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Correct Replacement Operator Mechanism for MaxxAir MaxxFan 7500K Roof Vent

Product Page this Question was Asked From

Continue Researching