Trailer Brake Spring Kit For 10 x 1-1/2" Brake Shoes

Question

Question:

Will these work on Dexter Axle 023-473-00 Trailer Brake Assembly Dexter 10 Inch Diameter x 1-1/2 Inch Width Electric Brake System Drum Brake Type 3000 Pound Axle Right Side

asked by: Darol B

0

Expert Reply:

If your brake shoes# bp04-065 are 10" x 1-1/2" you will need these brake springs # K71-362-00. The springs you were looking at # BP06-120 were for 2-1/4" shoe width.

expert reply by: Adam E

0

Answer 1

If you are going to try and find specific replacement parts for a set of electric trailer brakes then you need to know what brand you have and around the time they were made. If you do not have this then you have two options, trial and error or…

view full answer...

Answer 2

You will want the Replacement Brake Spring Set for Dexter 10" x 1-1/2" Electric Trailer Brake Assembly #K71-362-00. Then you will want the Replacement Trailer Brake Magnet Kit for 7" Brake Assemblies #BP01-068 due to the thinner hubs…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 5

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 6

I currently have three diffrent self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes which are attached for you below. eTrailer Electric Trailer Brake Kit part #AKEBRK-35-SA (3,500 Axles) Dexter…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

I sure can Bob and thanks for the information! Since you have a Lippert 3,500 lbs axle you'll be able to use the Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles item #AKHD-545-35-EZ-K, you were looking at. These have a 5 on 4-1/2 lug nut…

view full answer...

Answer 9

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

Hi Tony; the #BK2-100 and #TMK52VR come with the same size bearings and grease seal. The main difference is the Timken name. This is usually associated with a higher quality bearings that are made in the USA which also accounts for the higher cost.

view full answer...

Answer 12

You will need to measure the diameter of the spindles where the seal and bearings ride. Check out the picture I attached that shows where this is. You will need an exact measurement so either a digital or dial caliper will be needed. To pick out the…

view full answer...

Trailer Brake Spring Kit For 10 x 1-1/2" Brake Shoes

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching