Replacement Reservoir Tank for Lippert Hydraulic Power Slide Out Unit

Question

Question:

fluid container for pump has a crack in it and leaks fluid.

asked by: Mike M

0

Expert Reply:

Without knowing more info it's hard to know for certain what reservoir you'd need but we do have the Lippert # LC46FR which is a 2 quart reservoir for the Lippert hydraulic kits.

If your trailer had the # LC141111 this would be the correct replacement reservoir.

expert reply by: Jameson C

0

Answer 1

Yes, if you have a Lippert Trombetta style of hydraulic slide out then the #LC141111 is exactly what you need. This will replace the pump reservoir kit you have. As long as you see Lippert or LCI somewhere on the setup this will work well. Your 2004…

view full answer...

Answer 2

I went ahead and reached out Lippert and they were able to tell me that the mounting screws on the Replacement 2-Quart Pump Reservoir Kit for Lippert Components Hydraulic Power Unit #LC46FR measure 3" from the top screw to the bottom screw, and…

view full answer...

Answer 3

If your system is a Lippert (which it almost certainly is) then you can use the Replacement 2-Quart Pump Reservoir Kit for Lippert Components Hydraulic Power Unit #LC46FR. This replacement reservoir is compatible with the Lippert Hydraulic Power Unit…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

I spoke with my contact at Trailair and from your serial number we were able to determine that your trailer came with a 1621 HD pin box which is a long pin box style. I was unable to obtain the exact part number for your Trailair pin box but from the…

view full answer...

Answer 7

Good morning, Ron! The Andersen Ultimate Connection 5th Wheel Trailer Hitch System #AN67VR is compatible with your factory gooseneck hitch ball just as it is. The Adapter #AN27VR you're looking at just gives you a better connection than the…

view full answer...

Answer 8

Yes, the puck system used on the 2016-2019 Chevy/GMC trucks is different than the pucks used on the 2020 and newer trucks. So you would need a 5th wheel like the B&W Companion #BWRVK3710 for your 2020 GMC Sierra 3500 with an 8' Bed. If you…

view full answer...

Answer 9

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 10

There is only one option to replace a Lippert, which is now Curt, Turning Point. You will want the Gen-Y Hitch Shock Absorbing 5th Wheel to Gooseneck Pin Box item #GY48GR. As far as make and model goes. 5th wheel trailer pin boxes are not model…

view full answer...

Answer 11

Hey Craig, it sounds like you are asking if the Andersen Ultimate Connection part #AN67VR can be used in the bed of your 2025 GMC Sierra short bed that has the OEM rail kit. If so, yes it can but you will need to use the pop in ball adapter part…

view full answer...

Answer 12

Hey Bill, The Gen-Y Hitch Shock Absorbing 5th Wheel to Gooseneck Pin Box #GY48GR has an 18.08" measurement from the center of the coupler to the center of the first bolt holes. When switching to a gooseneck pin box from the Lippert Turning Point…

view full answer...

Replacement Reservoir Tank for Lippert Hydraulic Power Slide Out Unit

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching