Where to Look for Brake Controller Pigtail for Chevy Express Van

Question

Question:

Need to know were do look for the pigtail to install a brake controller

asked by: SCOTT

0

Expert Reply:

There is no standard for these vehicles, but we have found that the pigtail location on a Chevy Express should be taped and tucked under the driver side floor mat up towards the firewall. It may also be under the dash but near the emergency brake pedal so you will want to start there.

I have added a link to a video install of the Tekonsha Prodigy P3 Trailer Brake Controller # 90195 on a Chevy Express I recommend checking out.

expert reply by: Kyle S

0

Answer 1

The 30205 bearing that you referenced has an inner diameter of just under 1 inch (0.985 to be exact). We do not have this particular bearing or a hub that uses this size bearing available. The #L44643 bearing that you also mentioned has an inner…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 4

Thank you for all of the information and pictures! It looks like you should at least have some wiring already run on your 2019 Chevy Express Van 3500 so I'm just as confused as to why you don't have a round plug with a cap inside the…

view full answer...

Answer 5

The trailer brakes work on a separate circuit than the lights. You have a couple of options to control the electric brakes on the trailer. One option is to use an air over electric brake control, #HA100400C. This unit connects to the air brakes on…

view full answer...

Answer 6

Hey Anthony, It looks like there's a proprietary pigtail wire harness (p1072586) to connect to the factory plug behind the trim on the driver's side and the brake controller's wire harness. From what I can find some people say that…

view full answer...

Answer 7

Hey Cory, thanks for reaching out! I'd be more than happy to help you get your 1999 Dodge Ram 2500 set up for trailer towing! Here are the parts you'll need: - T-One Vehicle Wiring Harness #118329 - Universal Wiring Upgrade #ETBC7 - Mount…

view full answer...

Answer 8

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

The electric brake wire on the 2005 GMC Savana Van models would be connected in one of two ways. If your van came equipped with a factory 7-Way, then the blue brake wire is already ran from the 7-Way plug in the back of the vehicle and up into the…

view full answer...

Answer 11

If your 2019 Chevy Express Van 3500 has the tow package there will be a round connector taped behind the rear bumper that a 7-way like the part #A10-7072VP could attach to. Otherwise you'd need to install a 4-way first like the part #118392.

view full answer...

Where to Look for Brake Controller Pigtail for Chevy Express Van

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching