Best Looking Class III Trailer Hitch for 03 Acura MDX
Question:
Which is the most visually appealing of the Class III hitches for our 03 Aucura MDX. Thank you.
asked by: Dennis S
Expert Reply:
I would recommend the Draw-Tite Class III receiver, part # 75599. Once installed, the only portion of the hitch that will be visible at the rear of the vehicle will be the receiver tube (see photo).
To complete your towing system, you might also need the following:
Wiring harness with 4-pole trailer connector, part # 118336
Ball mount, part # C45010
2 inch trailer ball, part # 19247
1-7/8 inch trailer ball, part # 19260
Pin and clip, part # PC3
Locking hitch pin, part # e98882
I will also link you to install instructions and videos that you might find helpful.
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Vehicle End Connector
- Converter
- No Tow Package
- 4 Flat
- Plug and Lead
- Plug-In
- Visible
- Tekonsha
more information >
1-7/8" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 1-7/8 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 2000 lbs GTW
- Class III
- Draw-Tite
more information >
2" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 7,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 7500 lbs GTW
- Class III
- Tow Ready
more information >
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 8-1/4" Long - 7,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- Steel Shank - Gloss Black
- Drop - 2 Inch
- Rise - 1 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- CURT
more information >
etrailer Trailer Hitch Receiver Lock for 2" Hitch - Flush - 2-5/8" Span - Stainless Steel
- Trailer Hitch Lock
- Standard Pin Lock
- Keyed Alike
- Stainless Steel
- Fits 2 Inch Hitch
- Flush Pin
- 2-5/8 Inch Span
- etrailer
more information >
Pin and Clip for 2" and 2-1/2" Hitches - 5/8" Diameter x 3-1/4" Span
- Hitch Pins and Clips
- Standard Hitch Pin
- Fits 2 Inch Hitch
- Fits 2-1/2 Inch Hitch
- 5/8 Inch Diameter
- 4 Inch Span
- Draw-Tite
more information >
Product Page this Question was Asked From
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 350 lbs TW
- 3500 lbs GTW
- 5000 lbs WD GTW
- 2 Inch Hitch
- 500 lbs WD TW
- Concealed Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Q&A: Towing Capacity of 2005 Honda Pilot and Parts Needed to Tow Trailer
- Q&A: Does Trailer Hitch Receiver fit 2020 Acura MDX A-Spec
- Q&A: Recommended Equipment Needed for Towing with a 2017 Honda Pilot
- Q&A: Why Would a Vehicle Need a Power Steering Cooler
- Q&A: Transmission Cooler Recommendation for a 2005 Honda Pilot
- Q&A: Trailer Hitch Recommendation For 2007 Honda Pilot
- Article: 2024 Best Gifts for Haulers & Towers
- Article: How to Choose the Right Trailer Hitch Class
- Article: Brake Controller Installation: Starting from Scratch
- Article: How to Measure for Trailer Hitch Drop
- Article: Trailer Wiring Diagrams
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: How to Clean Weld Nuts for the Installation of a Trailer Hitch | etrailer.com