Can the Trailer Valet XL Trailer Dolly be Used on Grass

Question

Question:

Can you get turf wheels so it will go on grass? I would be interested in the XL.

asked by: Robert

0

Expert Reply:

The Trailer Valet XL Trailer Dolly with Chain Drive # TVXL2 that you are looking at actually has solid rubber tires that use deep treads so you can use it on tricky surfaces like gravel, dirt, or grass. It is meant for use on pavement or well packed surfaces but the deep tread does help as well. I do recommend using a powered drill and the included drill bit for your application though as traveling through grass will be a bit more difficult.

expert reply by: Jon G

0

J R.

7/6/2020

I have a 22’ boat approx 4500 lbs plus a tandem trailer. Going up a 2 degree incline cement drive. Will the Trailer Valet XL work for this?

Reply

Chris R.

7/10/2020

The Trailer Valet XL # TVXL2 can technically work on really small inclines like this, but it'll require a bit of work. Capacity-wise your boat trailer isn't an issue. Just keep in mind you may need to push a bit when going up the cement driveway.

Reply

Answer 1

You wouldn't want to try and move a trailer up an incline with the MT70881. The dolly itself would be fine but you would most likely not be able to pull that heavy of a trailer up an incline. And then if you somehow did get it going up the…

view full answer...

Answer 2

Yes, the Trailer Valet XL Trailer Dolly #TVXL2 will work in your situation. The solid rubber tires have treads which will give you traction in the grass/gravel/dirt situation you find yourself. As this is rated for trailers up to 10,000lbs with up to…

view full answer...

Answer 3

For your 2018 Toyota Tundra we have the Curt front hitch part #31198 and the Draw Tite part #65080 both as a confirmed fit and both really good options. Both install the exact same and have same capacities, but I like the Curt better as it's made…

view full answer...

Answer 4

Both the Ranch Hand Legend Grille Guard and the Curt Front Mount Trailer Hitch Receiver item #C31071 use the same method of install but different attachment points on the front end of the frame. There is one common bolt hole on either side that they…

view full answer...

Answer 5

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 8

The only difference between 7-Way Utility and 7-Way RV is the color of the wires. The pin outs are the exact same so either would work just fine with the other. If you check out the picture I attached you'll see that the functions are all the…

view full answer...

Answer 9

If your trailer has 7 wires running all the way back to the brakes, then yes, you can tap into the existing wiring. Each of your new brakes will have two wires for the brake magnet. One wire is for 12 volt power to the brake magnets and the other…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 12

Hey Alex, I can help you determine which Dexter EZ Flex fits your boat trailer but I don't have a way to know for sure at this time since we don't have that info. If your axle wheelbase is 33 inches then you'd want the part #K71-652-00 or…

view full answer...

Can the Trailer Valet XL Trailer Dolly be Used on Grass

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching