How To Bolt-On, Weld On Trailer Fenders

Question

Question:

The weld on trailer type fenders can you bolt them on I dont have a welder and also do you sell steps for them thanks

asked by: Hugh

0

Expert Reply:

Yes you certainly can. In order to bolt-on a set of metal weld-on fenders such as the Single Axle Trailer Fender part # HP29VR you will need a set of mounting brackets such as the Mounting Brackets for Trailer Fender part # CE26098G-2. If you do not have a 14" or 15" wheel, you will need to match the correct the trailer fenders to your wheel size in addition to matching the mounting bracket to your trailer fenders.

Unfortunately, the only trailer fenders we sell that have a step feature are plastic. For this you will need the CE Smith Single Axle Trailer Fenders part # CE19503-2 for 13" wheels, part # F008584-2 for 14" wheels, and part # F008585-2 for 15" wheels.

expert reply by: Conner L

0

Michael M.

4/26/2020

Ordering F008544-2 fenders.What mounting brackets do i need and how much are they?

Reply

Chris R.

4/28/2020

If you won't be using existing brackets the CE Smith # CE26098G-2 will work really well to mount the Fulton Single Axle Fenders # F008584-2.

Reply

Michael M.

4/28/2020

How much are the ce260986-2 brackets ?

Reply

Chris R.

4/30/2020

Pricing for the CE Smith Brackets # CE26098G-2 (linked below) is listed on the product page.

Helpful Links

accessories-and-parts/ce-smith/ce26098g-2.html

Reply

Answer 1

Thanks for the photo. Honestly 5 inches of clearance from the fender to the top of the tire is fine if that is what you desire. We normally recommend 4 inches to allow for the suspension travel whether with leaf springs or torsion axles to allow…

view full answer...

Answer 2

The length of the hardware used to secure a fender using brackets such as #CE26061G-2 is going to depend on how thick the trailer frame is where the brackets and fender will be installed. You could bolt all the way through the frame which would mean…

view full answer...

Answer 3

Yes, the Mounting Brackets #CE26098G-2 can be used to install the Stainless Steel Tandem Axle Trailer Fenders #HP88VR, just note that you'll need 4 brackets per fender so you need to order 4 of these kits since there are 2 brackets in the kit.…

view full answer...

Answer 4

I attached a picture that shows what type of lighting requirements are needed for a trailer over 80 inches in width as well as a link down below that covers this as well.

view full answer...

Answer 5

I attached a help article that details all of the various taillight requirements for trailers based on their dimensions. A good kit to start with would be the part #TL16RK, for an ID bar part #MCL84RB and then for red ID lights for the rear part of…

view full answer...

Answer 6

I have exactly what you need to replace the side guide rollers on your Catamaran Trailer. For this, I recommend the Yates Side Guide Roller for Boat Trailers part #YR12243-5. This roller is 12" long x 2-1/2" diameter and has a 5/8"…

view full answer...

Answer 7

The right and left orientation is determined if you are standing behind the trailer looking towards the tow vehicle. The left side is the drivers side and the right side is the passengers side. Tthe shorter brake pad will always be in the front of…

view full answer...

Answer 8

There is a flange on the Tandem Axle Trailer Fenders w/ Backing Plates #HP82VR that overlaps the backing plate that you'll use for the welding surface. When it comes to welding, we always recommend having this done by an experienced welder.

view full answer...

Answer 9

Thanks so much for the photos, and based on those, your 2018 Liberty Outdoors Little Guy Max travel trailer has a 3,500 lb Lippert square torsion axle, for which we do have the correct lift kit, which is the following: - Axle Riser Kit - Single…

view full answer...

Answer 10

You definitely don't have enough clearance so it is a wonder your wheels don't rub under suspension travel over bumps. Since your 2019 Little Guy Max travel trailer has torsion axles, the correct fit for that size is the Torflex Lift Kit -…

view full answer...

Answer 11

Since one end of a slipper spring is suspended instead of bolted to a hanger or shackle strap the Dexter Trailer Springs Over-Under Conversion Kit part #K71-385-00 and other likes them are considered unsafe for slipper springs. The only other option…

view full answer...

Answer 12

If your leaf springs are slipper springs, such as #WIH4, then you will not be able to use a Dexter over/under conversion kit, #K71-384-00. What you would have to do is cut off the hangers the leaf springs hang from and have new, taller ones welded on…

view full answer...

How To Bolt-On, Weld On Trailer Fenders

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching