What Is Hole Size For Mounting 2 Inch Round Trailer Lights With Rubber Grommet
Published 09/22/2010
Products Featured in This Question
Question:
What is the hole size for a 2 round light using a rubber groumet? Do you sell a bracket for the 2 round light? If so what is the part number? Thanks
asked by: Patrick R
Expert Reply:
The item you selected, Sealed 2-1/2 Trailer Light, part # MC57AB, is a 2-1/2 inch light that will mount into a 3 inch hole using 2-1/2 inch grommet, part # A55GB.
The hole size to mount a 2 inch round light flush mounted would be 2-5/16 inches. The grommet you would need for a 2 inch light would be 2 Inch Round Grommet, part # A54GB. If you are flush mounting your lights, the 2 inch light will sit inside the grommet. A 2 inch light similar to the one you selected is part # MC53AB.
We currently do not have a bracket for a 2 inch round light. We do carry 2 inch lights with an integrated mounting bracket such as 2 Inch Round Trailer Clearance Light, part # MC52AB.
Product Page this Question was Asked From
Optronics Trailer Clearance or Side Marker Light - Submersible - Incandescent - Round - Amber Lens
- Trailer Lights
- Clearance Lights
- Rear Clearance
- Side Marker
- Round
- Recessed Mount
- Submersible Lights
- Incandescent Light
- 2-1/2 Inch Diameter
- Amber
- Optronics
more information >
Continue Researching
- Shop: Trailer Hitch
- Search Results: tekonsha 9030 brake controller
- Search Results: 1117
- Search Results: 2010
- Search Results: ramp latch
- Search Results: break away switch
- Search Results: hopkins 41157
- Search Results: fender
- Shop: Curt Lunette Ring - Flat Plate Mount - 3" Diameter - 60,000 lbs
- Shop: Single Axle Trailer Fender for Enclosed Trailers - Steel - 15" to 16" Wheels - Qty 1
- Shop: B&W Turnoverball Underbed Gooseneck Trailer Hitch w/ Custom Installation Kit - 30,000 lbs
- Shop: Curt Pop-In Ball for Chevy/GM, Ford, Nissan, and Ram Underbed Gooseneck Hitch - 3" - 38K
- Shop: Ram Gooseneck Coupler w/ Load Bearing Pin - 8" Adjustment - Round - 2-5/16" Ball - 25K
- Shop: Brake Controller
- Shop: Peterson Grommet for 3/4" Diameter Trailer Lights - Round
- Shop: Tekonsha Voyager Trailer Brake Controller - 1 to 4 Axles - Proportional
- Q&A: What Size Hole Needs to be Drilled to Install 2-1/2 inch Optronics Clearance Light MC57RB
- Video: Comprehensive Review: 2" Round Grommet
- Q&A: Size Hole Needed to Install 4 inch Trailer Taillight that is Flush Mounted
- Q&A: Hole Dimensions for Hopkins 7-Way and 4-Way # HM48470
- Q&A: What Does Yellow Wire of 7-Way Molded Trailer Wire Connector H20044 Wire To
- Video: Beacon Light Mounting Brackets for Flint Hill Goods Headache Racks Feature Review
- Q&A: What Size Hole is Needed for Installation of 2 inch Round Trailer Clearance Light MC53RB
- Q&A: Replacement Bearings and Seal for Dexter Hub 8-147
- Q&A: Replacement Hub/Drum Assembly Needed for a Dexter 8-147 Assembly
- Article: Testing Trailer Brake Magnets for Proper Function
- Article: Breakaway Kit Installation for Single and Dual Brake Axle Trailers
- Video: The Low-Down on the Buyers LED Trailer Tail Light
- Video: Fusion LED Trailer Tail Light Review
- Video: Ultimate Overview of the LumenX LED Trailer Tail Light w/ Grommet and Plug