Installing Brake Controller on 1990 Ford F250
Updated 05/09/2015 | Published 05/08/2015
Products Featured in This Question
Question:
I have a 1990 Ford F250 with the towing package but I have never needed to use it until now. I have the factory harness with the jumpers but they state that the 3 wires in the cab are: RED from the battery, RED-green stripe for trailer brake lamps, BLUE for powered trailer brakes I understand that your controller has a white wire for ground black wire for battery power Is your blue wire for powered brakes and your red wire for brake lights? I read on your site that red wire was for cold side of brake pedal switch so I am a little confused. Thanks for any help that you could give.
asked by: Michael R
Helpful Expert Reply:
Having a truck that old with tow package wiring for installing a brake controller is a new one on me, but I can certainly help you determine which wire serves what function.
Just about every brake controller out there will have four wires exiting the rear of it. The black wire carries 12-volts to the controller. Having a direct fused or circuit protected connection to the battery is the best way to provide this power. The white wire is the ground connection. Some will say that simply grounding this wire to metal under the dash is sufficient, but the controller manufacturers recommend connecting this directly to the negative post of the battery. The red wire is usually connected to the brake stoplight switch, or a dedicated stop lamp signal like a third brake lamp. The stoplight switch is usually used because its the closest place to get a signal. This circuit is what alerts the controller that the vehicle brakes are being applied. The blue wire carries the output voltage from the controller to the 7-way connector at the rear bumper.
You can confirm that the red wire you found is the 12-v feed to the controller by using a circuit tester like part # PTW2993 or a multimeter on it. This circuit should show a constant 12-volts. The red wire with green stripes can be tested also. This wire should only show current when the brake pedal is applied-not with the turn signals or running lights. The blue wire should be the output circuit to the 7-way. If that all checks out, connect the red wire you found under the dash to the black controller wire, the red and green striped wire to the red controller wire and the blue wire you found to the blue wire of the controller. Extend the white controller wire through the firewall to the negative battery terminal.
This all assumes that your truck has a functional 7-way trailer connector on the rear bumper.
Product Page this Question was Asked From
Tekonsha Prodigy P2 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Electric over Hydraulic
- Splice-In
- Under-Dash Box
- Under-Dash
- Up to 4 Axles
- LED Display
- Single Trailer Only
- Tekonsha
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Wiring
- Shop: Brake Controller
- Q&A: Brake Controller and Wiring for a 1990 Ford F-250 Towing a 2 Tandem Axle Trailer
- Shop: Tekonsha BRAKE-EVN Trailer Brake Controller w/ Plug-In Harness - 1 to 4 Axles - Proportional
- Q&A: How Does a Proportional Brake Controller Work
- Shop: Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Shop: Curt Universal Installation Kit for Trailer Brake Controller - 7-Way RV - 10 Gauge
- Shop: T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Shop: Tekonsha Prodigy P2 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Shop: Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Search Results: gen y
- Article: Brake Controller Installation: Starting from Scratch
- Video: Comprehensive Review: T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector-118316
- Video: Setting up the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers on a 2018 Ford F-150
- Video: Trailer Wiring Harness Installation - 1990 Ford F-150
- Q&A: How to Test Brake Controller without Trailer Connected
- Search Results: gen~y hitch hitch adapters
- Video: Let’s Check Out the Tekonsha Replacement USCAR Trailer Connector
- Shop: Trailer Hitch
- Search Results: 7 pole adapter
- Search Results: tekonsha custom fit vehicle wiring
- Article: The Best Trailer Tongue Locks for Preventing Trailer Theft
- Video: Ultimate Overview of the InfiniteRule Lock for Gen-Y Hitch SnapLatches
- Video: All You Need to Know About the Gen-Y Torsion 2-Ball Mount
- Video: Review of Gen-Y Hitch Adjustable Ball Mount Stabilizer Bar Kit - 325-GH-0100
- Q&A: Fit of Curt Class V C15300 Hitch on 1986 Ford F-350
- Search Results: etbc7
- Q&A: Replacement 921 LED Bulbs for Interior Lighting
- Shop: Suspension Enhancement
on Trailer Brake Controller
