Will the P3 Brake Controller Work In Reverse when Backing Up a Trailer

Question

Question:

Will this controller provide braking action to my trailer helping control my boat and truck backing down a steep boat ramp?

asked by: Robert

0

Expert Reply:

Yes. The P3 brake controller # 90195 also works proportionally in reverse. You will need to put the controller in reverse mode though and this is outlined in the instructions, page 7, which I have linked for you. I have included a link to a video review of this controller as well.

expert reply by: Michael H

0

Answer 1

We do have an electric over hydraulic disc brake kit that will fit a trailer with two 7000 lb rated torsion axles. In addition to a hydraulic disc brake kit, you will also need a brake line kit, that is compatible with electric over hydraulic brakes.…

view full answer...

Answer 2

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 3

Yes, there is a measurement you can take to determine what size brakes you need and if they will fit your existing drums. You will want to measure the diameter of your drums. I have included a diagram detailing the dimensions you will need to find.…

view full answer...

Answer 4

What type of brake controller do you have? Is it a proportional or time delayed? Also, are you using the brake pedal or the manual override? If you have a proportional brake controller and you are using the manual override then you should see a full…

view full answer...

Answer 5

Your brake controller should be getting 12 volts of power going into the brake controller. The wire that feeds power to the brake controller is the Black wire. You can test this wire by using a multimeter part #PT89ZR. The amount of power coming out…

view full answer...

Answer 6

If you're in a situation where the maneuvering is going to take you more than two or three minutes, you'll want to put the controller in reverse mode. This will cancel the boost level if you have it set and cancel the hold feature. If…

view full answer...

Answer 7

The Tekonsha Prodigy P3 Brake Controller, #90195, does not have an on and off switch. It will go into sleep mode after several minutes of no activity. The power draw when it is in the sleep mode is so negligible that it will not discharge the…

view full answer...

Answer 8

The P3 brake controller, #90195, will go into a sort of sleep mode after it detects no movement for 15 minutes. While it is on it does not draw very much power. What you can do to make sure it goes to sleep is exit the truck after turning it off,…

view full answer...

Answer 9

If the trailer has an A-frame tongue on it, you should be in good shape unless you need to make a very tight 90 degree turn. We offer several different ball mounts in extended lengths. The longest ball mounts typically have a lower weight capacity.…

view full answer...

Answer 10

If the trailer is less than 1 inch off of being perfectly level either up or down then it will be perfectly fine. Having it slightly higher would be better because presumably the tongue weight of the trailer will pull it down a little. You could also…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Will the P3 Brake Controller Work In Reverse when Backing Up a Trailer

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching