Filter By Toolbox Application
Vehicle Style: 6 Foot Bed Change
Truck Tool Box Specs:
Features:
24" Long x 24" wide x 24" tall. Square liquid transfer tank; Brite-Tread aluminum; durable radius-curve design; stability baffles, cap, drainage plug and coupler for venting.
More Information >Truck Tool Box Specs:
Features:
48" Long x 12" wide x 16" tall. Topsider-style tool box; Brite-Tread aluminum; locking T-handle latch; drop down door with stop chains; V-stiffeners extend tool box life; sits atop truck-bed rails.
More Information >Truck Tool Box Specs:
Features:
24" Long x 24" wide x 24" tall. Square liquid transfer tank; NRT-coated steel; durable radius-curve design; stability baffles, cap, drainage plug and coupler for venting.
More Information >Truck Tool Box Specs:
Features:
24" Long x 24" wide x 24" tall. Square liquid transfer tank; NRT-coated steel; durable radius-curve design; stability baffles, cap, drainage plug and coupler for venting.
More Information >Videos
for Truck Tool Box
Help Articles
for Truck Tool Box
Expert Answers
for Truck Tool Box
Hey Steve, The B&W Patriot #BWRVK3255 you have would require base rails or a gooseneck hitch and an adapter in order to mount to the bed of the F-250. If you want to go with base rails then I recommend the B&W Custom Installation Kit w/ Base…
view full answer...Hey John congrats on the new truck! To add a set of air bags to your 2025 Ram 3500, I recommend the Air Lift LoadLifter 7500 XL Air Helper Springs item #AL57531. These fit both the 2WD and 4WD models and have a 7,500 lbs load leveling capacity. All…
view full answer...According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…
view full answer...Yes, the best option we can offer you to add fuel capacity is with the DeeZee Truck Bed Auxiliary Tank part #DZ91752X which should fit in the space you have between the cab and 5th wheel hitch no problem as it is only 9" deep. I don't have…
view full answer...The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…
view full answer...Probably not unless you want to cut that round hole into a 2-1/4" square. The Square A-Frame Jack w/ Footplate item #e74VV is designed for a-frame trailer's that have a square cut out not the standard 2-1/4" circular cut out which I am…
view full answer...Not that one Scott, but I have one that will. The UWS Truck Bed Fender Well Toolbox item #UWS01624 is too tall at 23-1/4". To keep below your bedsides you'll need to use the DeeZee Specialty Series Passenger's-Side Wheel Well Tool Box…
view full answer...I do recommend using two pairs of the Ultra-Fab Chock and Lock Wheel Stabilizers #UF21-001070 for your triple axle trailer. Doing so is going to give you the best amount of stability to limit the front-to-back rocking motion that will occur when you…
view full answer...The overall height including the cap for the DeeZee Truck Bed Auxiliary Tank #DZ91752X that you referenced is 22-1/2 inches. We've found that it typically fits pretty easily under tonneau covers like what you see in the attached picture, but you…
view full answer...I recommend the UWS Truck Bed Toolbox w/ Pull Handles #UWS07646 to go with your Access Toolbox Edition Soft, Roll-Up Tonneau Cover #A61409. It is low profile, 14-1/2" tall to allow you some extra space for hauling material, and is 20" wide…
view full answer...Hello Jack, thanks for reaching out. The Yakima LowRider Kayak Trailer is a great option for carrying tow Old Town sportsman 106 kayaks. The crossbars are 78" long so you will have room to spare with the kayaks side by side. Also, the tires have…
view full answer...Great question, Kevin. The Onboard Scale system on your 2024 Ford F-350 Super Duty works by essentially measuring how low the bed is sitting and it gives an estimated weight based off of that. If you added a suspension enhancement then that would…
view full answer...