Vehicle Style: 5 Foot Bed Change
Roll-Up - Soft Cover Specs:
Features:
Avoid the hassle of traditional, snap-style tonneau covers, improve gas mileage and upgrade the look of your truck with a TruXport. The cover attaches on top of your truck bed side rails with clamps and rolls up to store conveniently behind the cab.
More Information >Fold-Up - Soft Cover Specs:
Features:
Easy in, easy on - this EZ Fold truck-bed cover clamps onto your side rails in minutes, and it folds up in seconds to allow access to your cargo. The low-profile cover also looks sharp, and it stores behind the cab when not in use.
More Information >Fold-Up - Soft Cover Specs:
Features:
Extang E-series tonneau cover features a tri-fold vinyl cover and an easy-to-use clamping system for installation and removal. Lightweight aluminum frame. Full perimeter seal keeps water out and prevents leaks.
More Information >Fold-Up - Soft Cover Specs:
Features:
Outfit your vehicle with the Deuce 2 tonneau cover and enjoy dual functionality and dual accessibility. This one-of-a-kind vinyl cover folds back 30" to allow easy access to the front of your truck bed - or rolls up and stores behind the cab.
More Information >Fold-Up - Soft Cover Specs:
Features:
The Trifecta 2.0 tonneau combines the look of a soft cover and the convenience of a hard, folding cover. Tri-fold, vinyl cover has a rail-free design, and it includes a self-contained, easy-to-use clamping system for fast installation and removal.
More Information >Videos
for Tonneau Cover
Help Articles
for Tonneau Cover
Expert Answers
for Tonneau Cover
Hi Jeff; thanks for the question and sturdy is definitely a good word for the etrailer tonneau that fits your 2022 Ram 1500 with a 5-1/2 foot bed, the etrailer Hard Tonneau Cover #e35DR. It's made of a…
view full answer...The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.
view full answer...Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4"…
view full answer...A drop axle certainly can make it tough to reach the star wheel adjuster on a drum brake. The adjuster spoon tool we offer #W80630 has a 90-degree bend that will often let you get access to the adjuster even on a drop axle. Essentially you will…
view full answer...Your 265/70R17 size tire is around 31-1/2 inches in diameter. You want to make sure the tire cover you get is large enough and doesn't have to be stretched over the tire.…
view full answer...The Tow Ready wiring harness #118571 is rated for 7.5 amps for brake lights and turn signals and 7.5 amps total for running lights. The fuse that goes on the power wire connection to the battery is a 10 amp fuse. The wire gauge of the long 12 volt…
view full answer...Actually our etrailer.com brand brake assemblies are rebranded AxleTek assemblies. So we have the 8k left and right assembly set #AKEBRK-8 which is most likely what you need but these are 12-1/4 inch in diameter by 3-3/8 inches wide and attach with…
view full answer...The Tekonsha OEM Vehicle Wiring Harness #22121 that you referenced includes all the wiring and parts necessary to install a fully functional 7-Way connector and trailer brake controller. The included brake controller harness is compatible with and…
view full answer...Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…
view full answer...Unfortunately there are no plug-in adapters or harnesses that would allow you to replace the factory 4-way flat trailer connector with a 7-way or a 7-way and 4-way connector on your 2005 Ford F-150. To complete the installation for a brake…
view full answer...There is a solution for you, but the lift kits you referred to such as #K71-725-02 will not work with welded on torsion axles. The best option is for you to simply remove your torsion axles and use the Timbren Axle-Less Trailer Suspension System…
view full answer...Yep, you're exactly right; the distance from the center of the hitch pin hole to the welded gusset is indeed four inches on the Curt Ball Mount for 2" Hitches #C45112. So if…
view full answer...