Tow Bar Wiring Specs:
Features:
Removable LED lights provide signal lights for your towed car without you having to tap into the car's wiring or run wires under the car. Wireless transmitter plugs into your RV's 4-way connector and sends a signal to the magnetic lights.
More Information >Tow Bar Wiring Specs:
Features:
This complete kit includes everything you need to correctly display your RV's brake and turn signals on your vehicle tail lights. Includes coiled 7-way to 6-way cable and 6-way car-side socket.
More Information >Tow Bar Wiring Specs:
Features:
Get turn signals and brake lights on your towed vehicle without tapping into the wiring. Light bar plugs into the 12-volt port in your car, with a wireless transmitter that plugs into your 7-way. Keeps you safe and legal while flat or dolly towing.
More Information >Videos
for Tow Bar Wiring
Help Articles
for Tow Bar Wiring
Expert Answers
for Tow Bar Wiring
If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…
view full answer...I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's…
view full answer...If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…
view full answer...Your trailer looks awesome! The Road armor equalizers #LC696740 and Equa-Flex Cushioned Equalizers #LC279687 are both pretty similar in performance even though the Road Armor has two dampers. The main difference is the size of the equalizers. The…
view full answer...Assuming your Sprinter has the factory tow package with the 7-way at the rear bumper, in addition to the #RED24FR Redarc Tow-Pro Liberty Brake Controller, you'll also need the #3063-P wiring harness and the #331-TPH-017. The connector…
view full answer...I would be happy to! To flat tow your 2024 GMC Canyon Denali you will need the following parts: Tow Bar and Safety Chains - Roadmaster Nighthawk All-Terrain Tow Bar w/ LED Lights item #RM-676 Base Plate Kit - Roadmaster Direct-Connect Base Plate…
view full answer...I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need…
view full answer...What you need for your Isuzu NPR truck is a powered converter #C59236. It is compatible with incandescent and LED trailer lights. I have included a link to the installation instructions for you. This harness does require a direct connection to the…
view full answer...The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…
view full answer...I would be happy to confirm the parts you referenced fit your 2019 Chevy Colorado and are compatible together. I have listed them below, along with any changes, and attached installation videos. Roadmaster Nighthawk All Terrain, Non-Binding Tow Bar…
view full answer...Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand…
view full answer...If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…
view full answer...