1989 Suzuki Spare Tire Bike Racks

Change Make

Select Vehicle Model

--Select Model-- Samurai Sidekick

   Go

Available Models for 1989 Suzuki Spare Tire Bike Racks

Samurai

Sidekick

1989 Suzuki Accessories

Towing

1989 Suzuki Trailer Hitch

1989 Suzuki Trailer Wiring

1989 Suzuki Brake Controller

1989 Suzuki Base Plate for Tow Bar

1989 Suzuki Vehicle Tow Bar Brake System

1989 Suzuki Vehicle Tow Bar Wiring

Cargo Control

1989 Suzuki Roof Rack

1989 Suzuki Trunk Bike Rack

1989 Suzuki Vehicle Cargo Control

1989 Suzuki Spare Tire Bike Racks

Performance Accessories

1989 Suzuki Air Filter

1989 Suzuki Suspension Enhancement

1989 Suzuki Vehicle Lights

1989 Suzuki Tire Chains

1989 Suzuki Fluid Filters

1989 Suzuki Catalytic Converters

1989 Suzuki Vehicle Snow Plows

1989 Suzuki Radiator Fan

Vehicle Trim

1989 Suzuki Floor Mats

1989 Suzuki Vehicle Covers

1989 Suzuki Side Window Vents

1989 Suzuki Vehicle Tent

1989 Suzuki Replacement Mirrors

1989 Suzuki Windshield Wiper Blades

1989 Suzuki Windshield Covers

1989 Suzuki Vehicle Air Mattress

Jeep Accessories

1989 Suzuki Replacement Top

1989 Suzuki Roll Bar Cover

1989 Suzuki Questions and Answers

• Trailer Spare Tire Carrier Recommendation that can Be Used on 12 inch or 13 inch Diameter Wheels
  
• The Erickson spare wheel mount part # EM77316 that you referenced was not designed to be used on wheels smaller than 14 inches in diameter. The cap diameter is 5 inches which is typically too large to fit smaller wheels. If you measure the diameter of the mounting flange on your wheel and it's smaller than 5 inches in diameter though it would fit and work well. Otherwise you'd have to look into a spare carrier designed for the smaller wheel diameters like the CE Smith U-Bolt style carrier...
  view full answer...


• Will the Rear Bumper Support Need to be Removed for a Hitch on a 1989 Suzuki Sidekick
  
• Per the instructions, the rear impact bar that you referenced will need to be removed to install a trailer hitch like the Curt Trailer Hitch Receiver part # 11128 on your 1989 Suzuki Sidekick. The bar can then be reinstalled if the hitch is removed but it will need to be left off the vehicle while the trailer hitch is present. If you need any other parts for your Sidekick please let me know what they are and I would be happy to offer some recommendations. I have attached install instructions...
  view full answer...


• Weight of Rola Atlas Roof Cargo Basket # 59043
  
• The Rola Atlas Roof Cargo Basket # 59043 referenced in your question weighs right at 48 pounds. It has a weight capacity of 160 pounds and measures 56 inches long, 43-1/2 inches wide, and 4 inches deep.
  view full answer...


• Is Modification Needed to Front Bumper of 1989 Suzuki Sidekick with the Demco Base Plate Kit
  
• If you check out the attached photos of the Demco Classic Base Plate Kit # DM9518016 installed on a Suzuki Sidekick you can see that the arms to sit lower so there will be no fascia trimming. I confirmed this with my contact at Demco but if you want to be sure you can refer to the photos and where the tabs sit just to be sure. All of the Demco tow bars (Kwik # DM9511011, Commander II # DM9511012, and Dominator # DM9511008) are compatible with this base plate kit, as well as some of the...
  view full answer...


• Electric Brake Controller Recommendation for a 1997 Beaver Monterey
  
• Yes you can install an electric brake controller on your vehicle. As long as there is a stop light circuit that you can tap into (there will be) then you can install a brake controller on basically any vehicle. For vehicles like yours this is a very common solution for towing a trailer with electric brakes. Typically controllers that adapt your brake style to electric brakes are pretty expensive and no more effective than a good proportional controller like the P3 part # 90195 that you...
  view full answer...


• What is the Thread Pitch for Trailer Hub Wheel Stud Part # RG03-060
  
• The threaded pitch of trailer hub wheel stud # RG03-060 is 20 threads per inch and the diameter is 1/2-inch. See diagram to the right.
  view full answer...


• Can Curt Adjustable Hitch # 13703 Fit C-Channel Frame that is 72 inches Apart
  
• You'd want to have the C-channel of your frame boxed where you attach the Curt hitch part # 13703. This will be the only way the hitch will fit the frame and attach securely. You'll need to have a welder weld in a section of metal on the C-channel where you want to install the hitch so that you'd basically be installing it like the trailer had a boxed frame instead.
  view full answer...