UV-resistant cover installs over your roof vent so you can open the vent and operate the fan in any weather. Zero-Leak mounting brackets and hardware eliminate the need to drill into your roof for installation.If you are installing this vent cover over a Ventline E-Z Lift Ventadome roof vent, then drilling is not required. The E-Z Lift vent has mounting tabs with pre-drilled holes for installing the included hardware.
Vent allows air to circulate in and out of your enclosed trailer. Easily open and close with the sliding lever to adjust the airflow. Aluminum construction is durable, lightweight, and corrosion resistant.Features: Vent allows air to circulate in and out of your enclosed trailer Easy to open - just slide the lever to open and close vent Louvres direct airflow up or down depending on how the vent is mounted (4) 2" Holes in rear of unit allow air in and out Durable, rustproof aluminum front and back plates Insert is constructed of corrosion-resistant zinc-plated steel Specs: Overall dimensions: 12-1/4" long x 10-1/2" wide 2-7/8" Between mounting holes on top (center to center) 3" Between mounting holes on sides (center to center) Ventilation hole diameter: 2" Mounting hole diameter: 7/32"
Heavy-duty, 2-part vent will stand up to the elements for years. Exterior vent houses a baffle that directs any intruding rainwater toward corner drain openings. ... Features: Rugged, heavy-duty vent holds up to whatever nature can dish out Rectangular exterior piece is designed to shed rainwater while allowing air movement Sloped shape encourages water to run off Interior baffle directs rainwater toward corner drain holes Louvers on top allow airflow Built-in, threaded holes provide mounting points for interior piece Round interior piece has a sliding door that lets you control how much air flows in and out Gasket included Sturdy steel construction White powder coated exterior vent Zinc-plated interior grille Made in the USA Specs: Fits 6" diameter hole or smaller Exterior vent dimensions: 12" long x 10" wide x 2" thick Interior vent dimensions: 7-1/4" diameter x 3/16" thick Notes: 20 Screws (sold separately) required to mount exterior piece (4) #10/32 Machine screws (not included) required to mount interior vent.
RV range vent made to withstand regular kitchen use and travel conditions you face on your adventures. With a low profile design and secure latching mechanism, this vent is often chosen as an upgrade for direct replacement. ... Features: Durable, low profile plastic vent with 1-1/2" flange depth for your RV range exhaust Damper door opens easily on reinforced hinges 2 push-lock latches secure the door when closed Vent cover has sleek shape and open bottom venting area Cover and latched door are designed to withstand high wind speeds during travel Plastic rated for heat and developed not to fade, crack, or become brittle Includes mounting screws Made in the USA Specs: Dimensions Cutout: 10-3/4" long x 4" tall Outside: 12-9/16" long x 5-7/8" tall Flange depth: 1-1/2" 1- Year warranty
Durable, UV-resistant cover lets you run your RV roof vent any time and in any weather. Angled louvers allow smoke, heat, and odors to escape while keeping rain and debris out. EZClip pins allow the cover to be opened or removed for easy maintenance.The MaxxFan roof vent has pre-drilled holes in the side wall that are hidden under plastic plugs. Just remove the plugs and fasten the aluminum brackets to the side wall with stainless steel screws.
Durable, UV-resistant cover lets you run your RV roof vent any time and in any weather. Angled louvers allow smoke, heat, and odors to escape while keeping rain and debris out. EZClip pins allow the cover to be opened or removed for easy maintenance.The MaxxFan roof vent has pre-drilled holes in the side wall that are hidden under plastic plugs. Just remove the plugs and fasten the aluminum brackets to the side wall with stainless steel screws.
We have the Ultra-Fab Solar-Powered Plumbing Vent for Motor Homes - 7" Diameter x 3-3/4" Tall #UF53-945001 which is designed to be mounted on the roof. My recommendation is to use this roof vent and allow your side vents to stay as they…
Hey Allen, thanks for reaching out. For bolting on the etrailer Scissor Stabilizer Jacks #e36VV the recommended hardware is self-tapping 3/8" x 1" screws. If you use that, you won't need any bolts or washers or anything. You'll want…
To answer the last question first, a stabilizer jack such as #JSC-30 would be used until there was just enough tension to keep the trailer or RV from rocking. For actual lifting you would need a different device. So assuming that the RV was level…
Hey Robert, thanks for the information. To add rear stabilizer jacks to your dump trailer, I recommend a pair of the Square Direct Weld Jack w/ Footplate item #TJD-8000S. This jack has a 7,000 lbs capacity and is sold individually so you'll need…
Hey Phil, If you're looking for the factory wire harness for a plug and play connection you'll find a connector that's gray with a red/orange center like the plug on the Curt Custom Wiring Adapter for Trailer Brake Controllers #C51436.…
Mark, the Kodiak Disc Brake Kit #K2HR35DKG appears to be what you're looking for but you're going to need to verify which bearings your trailer uses right now to make sure it's compatible. The bearings, actuator #DX29FR and brake lines…
Hello Edward, We don't offer a KCD2-7-203, but from what I could find it was a DPST, on/off switch. The option we have for that which is four pins is the Single Labeled Mini-Rocker Switch #37213735. I'm not sure if this will fit as I could…
We have two options of replacement vent covers for the V2094 model, the white dome assembly, #BVD0449-A01, and the #BVD0449-A03 for smoke. These work for Ventline Ventadome roof vent models V2092, V2094, V2119, and V2128 after 2008. Pre 2008, please…
I have a solution for you but we do not have any standard grease caps with a 2.24" diameter like the #RG04-020 . I recommend going with the Bearing Buddy Bearing Protectors #BB2240 which will not only protect your bearings but provide an easy,…
It sounds like you have the older hub 22834 that is no longer in production that takes the outer bearing of part #1779 and inner bearing of part #2788. I was not able to find any other bearings that measure .093" inner diameter besides 1779 or…
It would seem to me that having an air vent and a fan vent is going to be sufficient, but you can always add another vent to help improve airflow. With that being said, you can add the 2-Piece Polypropylene Trailer Vent #HMAV2-AVT2 to provide you…
You will need to measure the diameter of the spindles where the seal and bearings ride. Check out the picture I attached that shows where this is. You will need an exact measurement so either a digital or dial caliper will be needed. To pick out the…
Durable, UV-resistant cover lets you run your RV roof vent any time and in any weather. Angled louvers allow smoke, heat, and odors to escape while keeping rain and debris out. EZClip pins allow the cover to be opened or removed for easy maintenance.The MaxxFan roof vent has pre-drilled holes in the side wall that are hidden under plastic plugs. Just remove the plugs and fasten the aluminum brackets to the side wall with stainless steel screws.
Perfect for use with high-powered fans, this cover has a wide vent area so that it provides more airflow than standard covers. EZClip pins allow the cover to be opened and closed with ease. No-drill installation on MaxxFan and MaxxFan Plus vents.If you are installing this cover over an older-model MaxxFan roof vent without mounting tabs, no drilling is required and all necessary hardware is included. The MaxxFan roof vent has pre-drilled holes in the side wall that are hidden under plastic plugs.
Perfect for use with high-powered fans, this cover has a wide vent area so that it provides more airflow than standard covers. EZClip pins allow the cover to be opened and closed with ease. No-drill installation on MaxxFan and MaxxFan Plus vents.If you are installing this cover over an older-model MaxxFan roof vent without mounting tabs, no drilling is required and all necessary hardware is included. The MaxxFan roof vent has pre-drilled holes in the side wall that are hidden under plastic plugs.
Perfect for use with high-powered fans, this cover has a wide vent area so that it provides more airflow than standard covers. EZClip pins allow the cover to be opened and closed with ease. No-drill installation on MaxxFan and MaxxFan Plus vents.If you are installing this cover over an older-model MaxxFan roof vent without mounting tabs, no drilling is required and all necessary hardware is included. The MaxxFan roof vent has pre-drilled holes in the side wall that are hidden under plastic plugs.
Manual lift roof vent removes unwanted hot air and moisture from your RV's kitchen or bathroom. The fan circulates air like a ceiling fan when your vent is closed. ... The shield blocks rainwater and other debris from entering through the vent and damaging the interior of your RV or camper. It also eliminates the need to install a separate vent cover. Fan Guard The fan guard protects your fan from water and debris when mounted on the side of your RV.
... Integrated rain shield lets you open your vent in any weather.It also eliminates the need to install a separate vent cover. Fan Guard The fan guard protects your fan from water and debris when mounted on the side of your RV. The guard slides over your vent with the solid end facing up to block rainwater and allow run-off, while the slotted end faces down to allow ventilation.
Manual lift roof vent removes unwanted hot air and moisture from your RV's kitchen or bathroom. The fan circulates air like a ceiling fan when your vent is closed. ... The shield blocks rainwater and other debris from entering through the vent and damaging the interior of your RV or camper. It also eliminates the need to install a separate vent cover. Fan Guard The fan guard protects your fan from water and debris when mounted on the side of your RV.
... Integrated rain shield lets you open your vent in any weather.It also eliminates the need to install a separate vent cover. Fan Guard The fan guard protects your fan from water and debris when mounted on the side of your RV. The guard slides over your vent with the solid end facing up to block rainwater and allow run-off, while the slotted end faces down to allow ventilation.
This vent cap creates a vacuum to remove odors and gasses from your holding tank and prevent them from entering your RV or camper. Maintenance-free cap has 2 installation options. ... Features: Vent cap removes odors and gasses from the black water holding tank in your RV or camper Prevents those odors and gasses from seeping into the RV Siphoning, maintenance-free design uses the air outside your RV to create a natural, upward vacuum in the vent pipe Operates immediately during any wind condition Eliminates the need to use additives, chemicals, or perfumed cover-ups Integrated bug screen helps keep out insects and debris Durable, UV-resistant polycarbonate construction 2 Easy installation options Modified installation upgrades the lid of your existing vent cap Complete installation replaces your entire existing vent cap unit Universal design is compatible with 1-1/4", 1-1/2", and 2" diameter pipe stacks PVC adapter sleeve (not included) may be needed for 1-1/4" and 2" pipe stacks Funnel is included for 1-1/2" pipe stacks Sealant or an adhesive (sold separately) is required Black color Base is RVIA 1192 compliant Specs: Overall dimensions: 4-1/2" diameter x 3" tall Mounting hole spacing: Side by side: 2-7/16" Across: 3-7/16" Collar diameter: 3-1/2" 1-Year warranty 360 Siphon Vent Cap vs.
... Vents on 3 sides provide extra ventilation. Includes mounting hardware.Features: Cover encloses your RV roof vent so you can safely open it at any time - rain or shine Lets in light and air while keeping the elements out Eliminates the threat of water leaking into your RV through the roof vent Gives you freedom to leave your vent open while driving down the road Swing-open lid lets you access your roof vent for cleaning Hinges on one end allow easy opening Screws on the other end keep the lid secured shut as you drive down the road Vents on 3 sides offer high level of airflow Can be used with high-power fans Streamlined, aerodynamic design reduces air drag Leak-proof installation with included mounting hardware Drill holes into the existing vent frame instead of the roof to prevent leaks UV-stabilized polypropylene holds up to the sun for years of use Specs: Fits standard 14" x 14" roof vents Dimensions: 22-1/2" long x 20" wide x 9" high 1-Year limited warranty Keep air circulating through your RV without letting in rain.
This vent cap creates a vacuum to remove odors and gasses from your holding tank and prevent them from entering your RV or camper. Maintenance-free cap has 2 installation options. ... Features: Vent cap removes odors and gasses from the black water holding tank in your RV or camper Prevents those odors and gasses from seeping into the RV Siphoning, maintenance-free design uses the air outside your RV to create a natural, upward vacuum in the vent pipe Operates immediately during any wind condition Eliminates the need to use additives, chemicals, or perfumed cover-ups Integrated bug screen helps keep out insects and debris Durable, UV-resistant polycarbonate construction 2 Easy installation options Modified installation upgrades the lid of your existing vent cap Complete installation replaces your entire existing vent cap unit Universal design is compatible with 1-1/4", 1-1/2", and 2" diameter pipe stacks PVC adapter sleeve (not included) may be needed for 1-1/4" and 2" pipe stacks Funnel is included for 1-1/2" pipe stacks Sealant or an adhesive (sold separately) is required White color Base is RVIA 1192 compliant Specs: Overall dimensions: 4-1/2" diameter x 3" tall Mounting hole spacing: Side by side: 2-7/16" Across: 3-7/16" Collar diameter: 3-1/2" 1-Year warranty 360 Siphon Vent Cap vs.
This 2-piece vent provides an inexpensive yet attractive way to ventilate your enclosed trailer. Round interior vent and half-moon-shape exterior piece are both constructed of black, UV-resistant polypropylene plastic that holds up to sun exposure.Features: Affordable trailer vent provides continuous ventilation for your enclosed trailer To increase ventilation, you can install more than 1 vent 2-Piece design creates a low-profile vent that's attractive both inside and outside your trailer Half-moon piece with flat, slotted side attaches to trailer's exterior Slots are on one side only, allowing you to position the vent for best airflow and to help prevent water from getting in Drain holes at the corners let out any water that does get in Round, slotted interior piece installs inside your trailer You can easily trim vent tube to fit thin walls UV-resistant, polypropylene plastic construction stands up to the elements Black color 9 Screws and sealant (sold separately) required for installation Specs: Fits 3" diameter hole in enclosed trailer Exterior half-moon dimensions: 8" long x 6" tall x 1-1/4" thick Flange width: 1/2" Interior circular piece dimensions: Diameter at flange: 4-1/8" Vent tube outside diameter: 2-15/16" Tube depth: 1-1/2" Flange width: 5/8"
This 2-piece vent provides an inexpensive yet attractive way to ventilate your enclosed trailer. Round interior vent and half-moon-shape exterior piece are both constructed of white, UV-resistant polypropylene plastic that holds up to sun exposure.Features: Affordable trailer vent provides continuous ventilation for your enclosed trailer To increase ventilation, you can install more than 1 vent 2-Piece design creates a low-profile vent that's attractive both inside and outside your trailer Half-moon piece with flat, slotted side attaches to trailer's exterior Slots are on one side only, allowing you to position the vent for best airflow and to help prevent water from getting in Drain holes at the corners let out any water that does get in Round, slotted interior piece installs inside your trailer You can easily trim vent tube to fit thin walls UV-resistant, polypropylene plastic construction stands up to the elements White color 9 Screws and sealant (sold separately) required for installation Specs: Fits 3" diameter hole in enclosed trailer Exterior half-moon dimensions: 8" long x 6" tall x 1-1/4" thick Flange width: 1/2" Interior circular piece dimensions: Diameter at flange: 4-1/8" Vent tube outside diameter: 2-15/16" Tube depth: 1-1/2" Flange width: 1/2"
Replace the vent cover on your Elixir trailer roof vent (made after 1995) or your Ventline trailer roof vent (V2094 - made before 2008) with this equivalent part. ... Features: Replacement cover for 14-1/4" x 14-1/4" roof vents Cover measures: 15" x 15" Lightweight, polypropylene domed cover Easy to install and operate White color Fits post-1995 Elixir trailer roof vents and Ventline pre-2008 trailer roof vent (V2094)
Replacement smoke colored vent cover for Ventline old-style rounded dome trailer roof vents.Features: Replacement cover for 14-1/4" x 14-1/4" roof vents Domed cover Easy to install and operate Smoke color Made of a polypropylene plastic Fits standard Ventadomes and post-1995 Elixir trailer roof vents 2-Year limited warranty
The tanks are full, the sun's beating down, and it's been a long day. This vent keeps things calm inside. It lets air out, keeps pests out, and eases tank pressure so your system stays quiet and off your mind.Highlights Keeps Air Moving: Helps your black tank vent properly to prevent pressure buildup. Two-Piece Design: Screened base and hood work together to keep out debris and pests. Easy Installation: Includes hose clamp, butyl tape, and mounting screws.
Replaces the lid for your Ventline, Maxxair, Fan-Tastic Vent, Ventadome, Jensen, and Elixir RV roof vent with a standard 14" x 14" opening.Features: Replacement RV roof vent prevents rainwater from getting inside your RV Fits Ventline, Maxxair, Fan-Tastic Vent, Ventadome, Jensen, and Elixir RV roof vents with a standard 14" x 14" opening Polypropylene construction is impact and UV resistant Easy installation with included hardware Included plastic track replaces the metal bracket if lid uses a track slider to open White color Specs: Overall dimensions: 15" wide x 16" long x 3-1/2" tall 1-Year warranty
Ventilate and balance air pressure in your RV's black tank with this exterior mounted vent system. The PowerVent base attaches to flex hose from your tank, and the PowerVent hood slides down over the base, allowing tank air to escape.Features: Exterior RV vent system lets air escape without allowing infiltration by bugs or rodents Base mount and cover make up the 2-piece vent system Required cutout is 1-3/4" and requires a flex hose line from your tank to the vent location Hose connects to the screened filter base like a water plate Cover slides over the top and is caulked in place Includes base, hood, Oetiker hose clamp, mounting screws, and butyl tape Made in the USA Specs: Cuout required: 1-3/4" diameter 3-Hole screw pattern 1- Year warranty
Filters
