!Outback Wagon  x   >   !Seaflo  x   >   Dutton-Lainson  x   >  

include two 4 ft set of rollers or one 4 ft | The Dutton Lainson 4 foot roller bunk part # DL21740 is a set of two roller bunks. |

Are they priced as a set of 2? What is the overall width across the three rollers? Are the rollers safe to be used on a boat with a painted hull? Thanks | Yes, the Boat Trailer Deluxe Roller Bunks are sold in a pair. The roller sets are 4-5/8...

What are the diamentions? Length? | The dimensions of the Slotted Bunk Bracket for Boat Trailers, by Dutton-Lainson, item # DL21584, are as listed below. 10 inches Overall length 2-3/16 Inches Overall Width 1-7/8 Inches Inside Width 3/8 Inch...

Need to know sizes, length and width. Than you | The dimensions of the Boat Trailer Roller Bunk Bracket for Dutton-Lainson Roller Bunks Parts DL21754 & DL21755, item # DL21762, are as listed below. 10-3/4 Inches Overall length 3 Inches Overall...

I need to know how long and wide this part is in inches. Thank you. Robert | The dimensions of the Slotted Bunk Bracket for Boat Trailers, by Dutton-Lainson, item # DL21584, are as listed below. 10 inches Overall length 2-3/16 Inches Overall...

Can this product bet set up for V hull type boats? | Yes, you can use the Boat Trailer Standard Roller Bunks # DL21755 on a boat that has a V hull. These can be attached to the edge of 2" X 4" Bunk Boards # CE27820 or to Boat Trailer Roller...

Can i use this product on my pop up camper to lift it up annd install my safety braces. Cables broken on camper | Brophy Cable Camper Jacks # CJ41 are designed for truck bed campers and for truck toppers and camper shells but for your pop-up...

We have a Dutton Laison winch set up for hoisting the mast of a light plant. Was wondering if you could recommend a replacement motor or winch set up. Thanks. | The Dutton-Lainson StrongArm Electric Winch # DL25727 is likely going to be your...

Need a replacement winch for a Shelby 5460A. What options do you have and what is the bolt hole pattern? | The Fulton High-Performance 2-Speed Trailer Winch part # F142412 is the perfect replacement for a Shelby 5460A. It has a two speed operation...

How much does the worm gear winch weigh? How much would it way with cable spooled on it? I’m only lifting a 175lb boat, I need a small one, plus one with Shepherds hook operation. Suggestions on model?? | The Dutton-Lainson Hand Winch - Worm...

Is there a certain way to hook the circuit breaker up, or does it not matter | When installing the Dutton-Lainson Wiring Harness for DC StrongArm Electric Winches # DL24151. The ring terminal with the circuit breakers on it will attach to the...

My trailer tongue is 3inch x 4. Your jacks are advertised to fit tongues that are 3inch x 5. Will the jack plates adjust down to 3inch x 4inch tongues? | Yes, the Dutton-Lainson Trailer Jack # DL22457 that you referenced can fit trailer frames...

Where can i find 10 - 11 foot bunk boards? I have 22.4 foot Lowe deck boat and there are only two cross members in the trailer frame to support the bunk boards. So two 5 footer will not work. i was hoping to replace the wooden ones with metal...

how do you release quick connects | Quick connects like the Dutton-Lainson Electrical Quick Connects # DL24086 that you referenced do not have a release latch built into them. Basically you just slide them apart. They can sometimes be difficult...

I bought a 2007 Monaco Diplomat 40SKQ and I want to Flat Tow my 2011 Ford Flex SEL depending where Im going. is it possible and what equipment do I need | With etrailer, it's possible. For your 2011 Ford Flex SEL you can use this base plate...

I need a winch to lift deer. 1. It needs to be able to hold load if handle is let go 2. It will get very muddy and wet. So i need one that will take the elements. 3. Rated for 500lbs. minimum. 4. Free wheeling. 5. Able to use the fiber rope....

How many bolts or screws are needed to hold down each section I am using a 5foot and a 4foot on each side for an 18foot boat approx. 2400# | A minimum of two bolts will need to be used to install each Dutton-Lainson Roller bunk part # DL21741....

I have a 18foot Javelin bass boat with 115 HP outboard and of course loaded with all the gear it can hold. Ive had two back surgeries and not lookig to add the third and am looking for some relief. The original hand-crank winch is still operable...

Hi. WHen you say fits 15inch wheel is that saying that it fits a 15inch tire or 15inch rim? I have a spare 22inch trailer tire that Im trying to mount. 22inch is the dia. of the entire tire. Any suggestions if this model wont fit? Thank...

Would you be able to give me the current direct replacement model # of a Dutton-lainson jack for the model #203295C Dutton-lainson trailer tongue jack 1000 lb. tongue weight capacity from 2007? | The current version of the Dutton Lainson Trailer...

I wanted to know if this part would be a good replacement for my winch. I have a 1998 Starcraft Ventura pop up model # 2406. Thank you for your time. It is a single cable design and the winch is mounted to the front of the pop up trailer. |...

“Miter bearing and gear kit for jacks with 600 lb to 1,000 lb capacity manufactured after 1996, but before 1997”. Too ?? | Replacement Miter Gear Kit for Dutton-Lainson Trailer Jacks # DL22447 only fits certain 600 to 1,000 pound capacity jacks...

I have a Premier 22.5 tritoon. Will the pontoon style roller guides work with this boat? If not, is there a product that will? | Roller bunks like those shown on the linked page will work just as well on a 3-hull tritoon as on a pontoon boat. If...

I want to order a replacement handle and hardware for the DL2000A, what is the part number please? | I was able to verify with the manufacturer, Dutton-Lainson, the exact replacement handle you need for your Dutton-Lainson 2000A winch, which...