Axle Seal Replacement for AL-KO T52 Trailer Axle
I have a keystone camper alko axle t52-3 and need to figure out what axle seal it uses without tearing it all down before hand | Your AL-KO T-52 axle has # 42 spindles that use hub assemblies with a # 25580 inner bearing and # 15123 outer bearing....
Torque Spec for Square BT8 Spindle for 2,000-lb Trailer Axles
Looking for some extra detail, specific to Torque Rating if you have it. Cheers! | If you're referring to the spindle nut on the Square BT8 Spindle for 2,000-lb Trailer Axles part # TRU97FR. there is no torque spec. There is no torque spec for...
Replacement Bearing Kit For a 2016 Forest River Wildwood 31QBTS Travel Trailer With 5,200LB Axles
I am not sure how to determine the type of axles I have on my 2016 Wildwood travel trailer. The model number is a 31QBTS. Could you tell me which kit is the right one for this trailer? Thank you. | Your 2016 Forest River Wildwood 31QBTS is...
Do the 5,200 Lb Dexter Trailer Axles Come With Leaf Springs
Can you tell me how long the leaf springs are that comes with this axle? I am upgrading a trailer with tandem 3500# axles to 5200# axlesPN6340624-EB. Will the equalizer that is used currently for the 3500# axles be the same size for the 5200#...
Spindle Washer to Fit 1 Inch Diameter Spindle
hello. I am looking for a washer to go between my castle nut and bearing on a small 5x8 trailer. I took a measurement of the spindle being 1.06. will item number Item # SW1000 work for this application. thanks! | The Washer For 1" Spindle...
Do I Need a Washer with Castle Nut to Install Dexter Trailer Idler Hub Assembly for 2,000-lb Axles
Can you confirm the Dexter hub 8-91-05UC1 does not require a washer between the castle nut and outer bearing? My trailer didn’t have a washer on either hub. I contacted Dexter and they said that hub doesn’t require a washer and none of the...
Replacement Hub and Spindle for Dexter 69-46 Axle
Hello, Im looking for a hub assembly and a weld on spindle for a torsion axle. The part numbers are Dexter 69-46, and on the hun is 8-259235. The hub is 5 on 4.5. Any help would much appreciated. | The Dexter 69-46 axle has a straight spindle...
Best Replacement # 10-36 Grease Seal
i also need 4 grease seals for the drums. 8 lug. 2007 cameo rv. 36 foot. do you know which seals will work? best seals. old seals say dexter 10-36. thanks | To replace your Dexter 10-36 grease seals I recommend using Grease Seal # GS-2250DL....
Replacement Trailer Axle Needed with 72" Hub Face and 54.5" Spring Center Measurements
I was wondering if you guys could make a custom axle? I am looking for a 72 inch hub face with 54.5 spring center. | Thanks for reaching out! I have a solution for you, but unfortunately we only offer some set choices when it comes to axle...
Trailer Spindle & Hub With 5 on 5-1/2 Bolt Pattern
Do you sell a 5 stud, 5.5 inch bolt circle hub that fits this spindle? | While we have an option for you, the Agricultural Spindle # TRU54FR uses uncommon bearings, so there isn't a hub for it with a 5 on 5-1/2" bolt pattern, just the 4 on 5"...
Availability of Dexter Hub Kit with Grease Seal Having 2.25-Inch I.D. and 3.376-Inch O.D.
Do you sell this kit but with the 2.25inch I.D. grease seal instead of the 2.125inch grease seal? Dexter Trailer Hubs and Drums - 8-201-9UC3-EZ | We do not offer the Dexter hub kit # 8-201-9UC3-EZ with a 2.25-inch inner diameter grease seal...
Replacement 72 Inch Long 2,000 Pound Trailer Axle
I need replacement axles for a trailer. The axles are 72inch long But when I measure the spring centers, it measures approximately 57-3/8inch in front and 57-1/8inch in rear. Will the 58inch spring center axles work, or will I have trouble getting...
Easy Way to Grease a Hub that is Missing EZ Lube Zerk Fitting
The hubs on my 1993 Ranger Trail trailer supposedly have EZ Lube hubs but there is no zerk fitting on the end of the spindle. The end of the spindle has a very small hole in the center with what appears to be three even smaller holes around...
How to Measure a Trailer Hub for the Correct Size Grease Cap
looking for dust caps rubber plugs and covers for 11\16 shaft 1995 model boat trailer I think its ez lube help | You would need to measure the inside diameter of the hub opening to determine which cap size is needed. You would want to choose...
Selecting Suspension Components for 1985 Skyline Trailer
I see the expert answered that you could assemble a kit, how do I go about getting a equalizer kit with 3 1/8-inch shackles and * spring bushes for my 1985 skyline 2360 ,ally badged,5er? | You can select individual parts such as shackle straps,...
Does Trailer with 1-1/16 inch Spindle Need 1-1/16 inch Diameter Washer
Hello: I cannot find 1 1/16inch spindle washers D-washer but any would work. Put new 1 1/16inch bearings on to trailer spindle, cannot find the 1 1/16inch washers? Thanks for any guidance | While your spindle may have a diameter of 1-1/16...
What Material is TruRyde TRU37FR 5.2-7K Trailer Spindle Made From
What Material is this machined from? | Acccrding to TruRyde, the # TRU37FR for 5.2 to 7K capacity trailer axles is constructed of cold rolled 1045 steel bar stock. The spindle is compatible with a # 25580 inner wheel bearing, the outer bearing...
Recommended Seal for a Boat Trailer That Uses 07100 Bearings
I have some old 07100 wheel bearings I believe Im replacing them with the L44643 bearings trying to get a part number for the correct grease seals. | If your hub uses the # L44643 as an inner and outer bearing, you will most likely need the...
Would Too Long of Equalizer on Trailer Suspension Cause it to Be at Angle
I bought a used trailer, is the equalizer to long? I measured eye to eye and it’s 7 3/4. Pictures front of the trailer to the right. | If your trailer is sitting perfectly level and the equalizer is sitting at an angle then yes I would agree...
Compatibility of MR46ZR Shackle Upgrade Kit and TREQ356 Equalizer
I have a 2010 Forest River Sandstorm 5th wheel, that I want to upgrade to a wet bolt suspension. I have EQ-356 equalizers and 1-3/4 wide springs. I dont see a full kit for this set up, if I purchase 2 TREQ-356 from you and one MR46ZR shackle...
Determining Which Axle For Custom Tear Camper Weighing Up To 1500lbs
Im having a chassis built for a tear camper at a local shop and would like to purchase the axles, springs, and wheels from you. Can you recommend a set up for my particular application? The chassis is 59-1/2inch wide, and 108inch long. The...
Determining Which Replacement Grease Seals Fit Dexter Axle Model D52 On 2000 Shasta Pheonix 278BH
I am trying to find out what seals I need for a Dexter D52 axle. On the axle plate it reads Dexter Axle P-1 Model D52 SLR 13.3 SN D4667001 4,000 lb capacity. I dont know exactly what the bolt pattern is, but I know it is a 6 bolt wheel. Goes...
Availability Of Bearing Buddy Bearing Protectors Smaller Than 1.980" In Diameter
I have a 5 lug wheel. And the cap is just under 2” the bearing buddy I had to get. In an emergency that fit was Napa part 821-2204 is there a smaller cap on here? | I would be happy to help! The Bearing Buddy you purchased measures 1.980" O.D...
Heavy Duty Shackle Kit with Wet Bolts for Triple Axle Trailer with TREQ356 Equalizers
Hello, I have the TREQ356 equalizers on my triple axel toy hauler with 1 3/4 springs and 2 3/4 shackle straps. I would like to replace the equalizers and the shackle bolts with heavy duty shackle straps and wet bolts. I dont see any options...
Filter Your Search
Contact and Help