Easy Way to Grease a Hub that is Missing EZ Lube Zerk Fitting
Published 08/15/2014 >
Question:
The hubs on my 1993 Ranger Trail trailer supposedly have EZ Lube hubs but there is no zerk fitting on the end of the spindle. The end of the spindle has a very small hole in the center with what appears to be three even smaller holes around the center hole. How do you lube the spindles? I bought one of the needle point tips to put on my grease gun but the grease justs comes out around the tip and does not go into the spindle. Can you tell me what I have and how to make it work? Thanks,
asked by: Don J
Expert Reply:
If it's missing the zerk fitting the easiest solution I could recommend for you would be to replace your grease caps with Bearing Buddies. Bearing Buddies replace the grease cap and provide an easy way to grease hubs.
In order to pick out the correct bearing buddy you will need know the pilot hole of your hub with a dial caliper. To do this, remove the wheel and tire and remove the grease cap from the center of the hub. Usually it is a metal cap that is just lightly hammered into place. Use a screwdriver to pry off the cap.
Clean the grease off and measure the opening.
Once you know what you have check out the link I attached to see which would be the correct product for your hub.
Product Page this Question was Asked From
#84 E-Z Lube Spindle w/ Brake Flange for 3,500-lb Trailer Axle - 1-3/4" Diameter
- Trailer Spindles
- EZ Lube Spindle
- With Flange
- L68149
- 1-3/4 Inch Diameter
- Round
- For 3500 lb Axle
- TruRyde
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Search Results: castle nut
- Search Results: spindle nut
- Search Results: 4 on 4 hub
- Search Results: wiring
- Search Results: flat tow wiring harness
- Search Results: galvanized hubs
- Q&A: Can a Passenger Side Tail Light Be Used on the Driver Side of a Trailer
- Shop: Trailer Idler Hub Assembly for 3,500-lb Axles - 5 on 4-3/4 - Pre-Greased
- Video: Review of the Unitized Oil Seal for Trailer Hubs
- Shop: Grease Seal - Single Lip - I.D. 1.938" / O.D. 2.510" for Mobile Home Utility Axle
- Shop: Lippert Spindle Nut Kit w/ Round Washer - For 2,200-lb to 4,400-lb Axles
- Shop: Trailer Idler Hub Assembly for 3,500-lb Axles - 5 on 5 - Pre-Greased
- Search Results: trailer hubs and drums
- Shop: Dexter Unitized Oil Seal - Double Lip - I.D. 2.250" / O.D. 3.376" - 7K to 8K Axles - Qty 1
- Q&A: Is There a Double Lip Seal To Replace the Dexter 10-40 Single Lip Seal?
- Shop: Combination LED Trailer Tail Light - Submersible - 6 Function - 11 Diodes - Passenger Side
- Shop: Combination Trailer Tail Light - 7 Function - Incandescent - Square - Red Lens - Driver Side
- Q&A: How to Add Automatic Hub Lubrication to a Trailer Without E-Z Lube Spindles
- Q&A: Replacement Hubs for a Hudson Bros. Trailer with 5-Spoke Utility Hubs
- Q&A: Diameter/Height of 4.80/4.00-8 and 5.70-8 Tires
- Q&A: Comparing 12" Tire Options ST145/R12 And 5.30-12
- Q&A: Recommended 5.30-12 Tire And Wheel Combo For A John Boat Trailer

