Result: knobs

Then reinstall the knob and secure the cover. He said you will want to do this on both sides of the bed. | front corner wants to raise up in wind . is there an extra clamp you can put on that corner? 2018 Chevy Colorado |...

All other hardware (bolts, nuts, knobs, etc.) would have to be either purchased through Brophy or if it's not too damaged you can take it your local hardware store to find replacements for much cheaper than going through a manufacturer and paying for shipping. |

The Redarc Tow-Pro Elite Trailer Brake Controller # RED44FR with Custom Wiring Adapter # 3020-S will give you what you want - a brake controller that is completely out of your way so there is no bulky unit underneath your dash. The Tow-Pro's knob will allow you to install the knob anywhere you like which makes the unit extremely convenient. |

If the clamp like the part # EX1034 is tight even after unscrewing knob that would mean it's either seized up and would need to be sprayed with some WD-40 to try and release it or it is some how binding up to the shaft of the threads. |

Also, you can position this bracket a couple of different ways so you can have the knobs pointed in different directions depending on how the bracket is oriented. | I have a 2016 Jeep Wrangler with a Mopar Trailer hitch? Will...

Hey Thomas, the clamp like the part # EX1034 is tight even after unscrewing knob that would mean it's either seized up and would need to be sprayed with some WD-40 to try and release it, or it is somehow binding up to the shaft of the threads. |

You cannot put a shank adapter like the # 853-7489 on the # TH23JV because of the locking knob system that keeps the shank firmly in place in the shank when installed. | Does this work to adapt a 1.25 T2 Pro XTR? Item TH83JV...

If your rack uses a standard hitch pin or a threaded hitch pin this should work well for you, but if it uses a different style of attachment like a tightening knob that pins the rack into the hitch this probably wouldn't work well. |

When it is time to remove this tonneau cover all you have to do is the following: fold the tonneau cover, slide the clamps toward the center of the truck bed, and undo the torque knobs at the bulkhead of the truck bed. It weighs just 35 lbs, so it is not particularly heavy. |

The Apex XT has a SnugTite so you can install and remove the rack simply by turning the knob, and at 35 lbs is 8 lbs lighter than the Curt # C18065. | Is this hitch rack quick and easy to install and remove? It would not stay...

When the bike rack is fully ed into the Draw-Tite receiver on my 2016 Subaru Outback the knob to release the swing arm hits the bumper. The Draw-Tite has two holes. | When the bike rack is fully ed into the Draw-Tite receiver...

At the top of the page the photos show a plastic latch and knob adjustor for the tenion , and at the bottom pictures it shows a metal latch with an automatic spring adjustor ? | Good morning, I am going to buy a tonnaeu cover...

This unit can produce 144 gallons of hot water an hour and has a thermostat that will allow you to change the temperature by the degree instead of just a knob with an arrow saying hotter or colder on it. | Hi, I am looking...

This rack allows for tool free installation, if you turn the knob you tighten the rack in the hitch receiver and eliminate any movement between the rack and your hitch receiver. | I have a 2018 Jeep Wrangler and just had a...

The NV 2.0 can be tilted down - even with the bikes loaded - with the press of a handy foot lever; it does not require any tools to install into your hitch as you'll only need to turn a knob to tighten the shank in the hitch and this also works as an anti-rattle device for a quiet ride. |

We used to carry the Yakima SwingDaddy that you mentioned and it had a distance of 6 inches from it's pin hole to the back of the knob for the swing mechanism. So you'd most likely have some contact there. | Weve got a hitch...

So I would use wheel locks and a coupler lock such as # FA86-0015-318 as an example (there are many types of coupler locks) similar to how a door might have a lock at the knob and a dead bolt lock. Now, if only the tow vehicle was that secure. |

If you are thinking about going that route, I highly recommend taking a look at the Kuat Beta # B202-114 which weighs less than 13 lbs and has dual-strap cradles along with an anti-rattle hand knob. When using a hanging rack it's possible you'll need a bike frame adapter bar, # 64005, if your bike is dual-suspension, has a step-through frame or you want to carry a small children's bike. |