A-Frame Tongue Jack Recommendation with Drop Leg
Is there an A frame tongue jack, round, with drop leg? | We do have a variety of A-Frame tongue jacks that come with a drop leg. Out of our linked selection I recommend going with out 3.5K electric trailer jack which comes as a hardwire install...
Will the Bulldog Powered-Drive Kit for Single-Speed Jacks Work On a Two Speed
Will the bulldog motor 182420 kit mount up right with a bulldog 2 SPEED jacksfor instance 183416 or just the single speed jacks? | The Bulldog Powered-Drive Kit for Single-Speed Jacks part # BD1824200100 as the title states is for single speed...
Dimensions and Installation of Bulldog Collar-Lok Coupler
On trailer coupler BD028243, what are the exact measurements outside width, inside width, height? Does it fit OVER or INSIDE a 3inch channel tongue? Thanks! | I went out to the warehouse and took some measurements of the The Bulldog Collar-Lok...
Pipe Mount for Square Bulldog Jack Compatible with Dimensions
i am thinking about either 195352 or 195368. i want to make it removable. does the 500339 pipe mount fit these square jacks and will the 500240 weld on frame mount fit the 500339. thanks | The Bulldog Replacement Pipe Mount for Swivel Jack...
Trailer Coupler Lock For Bulldog Coupler
I am looking for a hitch lock for your part # BD44150WH301. That is a Bulldog heavy-duty cast head coupler. 2 5/16’ | When using a bolt-on coupler such as the Bulldog # BD44150WH301, locks such as the Master Lock # ML389DAT help to prevent...
Can Bulldog Square Jack # BD182701 be Used on 18 Foot Car Trailer
I HAVE A 18FT CAR TRAILER WITH 2 FT DOVETAIL, My Question is will this jack work on it or not , i like the JACK IN qUESTION If YOU THINK IT WILL WORK WHAT IT THE PART NUMBER FOR THE HANDEL | Bulldog Square Jack # BD182701 is a weld-on...
What Is Difference Between Bulldog Velocity Jack part # BD185400 # BD185402
I understand the difference between the two jack are that one comes with a remote and one doesnt. Few questions: 1 why is the one without the remote more expensive? 2 is the remote hard wire or wireless on the model that comes with a remote...
Bike Rack Solution for 2006 T@B Tear Trailer
I have a 2006 T@B tear at that time made by Thor that has the original Al - Ko coupler connected to the mechanical surge brakes. I would like to use a double receiver hitch so I can connect my bike rack but the lift handle on the existing coupler...
Recommended Pintle Hitch with 2-5/16 Inch Hitch Ball for Lunette Ring and Coupler Compatibility
I want to change the Lynette ring with a 2 5/16 hitch | It sounds like you are looking for a pintle/ball combination hitch like the Pintle Hook Combo with 2-5/16" Ball # C48200. If you want a hitch mounted option, then you can use the Curt...
Replacement Bulldog Model 1550220117 A-Frame Trailer Jack
I have a Bulldog jack Label F3351A #1550220117 with a bent inner pipe. Can I buy a replacement? If yes what is the cost, if not what is the cost of a new one. | I do have a solution for you, however there is not an inner pipe/tube replacement...
Comparing Bulldog Tandem Landing Gear Set and Bulldog Square Jack with Caster Base
Hello, BD195368 or BD500162 | The Bulldog Tandem Landing Gear Set part # BD500162 is designed for use on 5th wheel trailers. The jacks operate as one when attached with the cross-shaft. The Bulldog Square Jack with Caster Base part # BD195368...
Will Bulldog A-Frame Jack Fit Bulldog Collar-Lok A-Frame Coupler
Just want to confirm that the Bulldog jack - part number BD155033 - will fit into this coupler. | Yes, the Bulldog jack # BD155033 is an exact fit for the # BD028463 Bulldog coupler. Both the jack and the coupler's hole are 2-1/4 inches. Most...
5,000 lb Bulldog A-Frame Jack With Short Retracted Height
Im looking for an A Frame jack that retracts as far as possible as I have had too much trouble with A frame jack legs dragging even when fully retracted. Im looking to add a leg/pedestal so amount of jack travel is less important. I would prefer...
Which is Stronger a Rack and Gear Type Trailer Jack or Screw/Nut Trailer Jack
I am interested in the difference in weight capacity of comparable sized rack-and-gear jacks vs. the more common swivel jacks with fixed internal nut used on most boat trailers. On your site you say: But the rack and gear jacks are also rated...
Recommended Coupler For Aluminum NEO 24 NACX A-Frame Trailer
I have a full aluminium NEO 24 NACX do I have to weld this or can I bolt it on like the original set up I dont see any holes on the coupler other than 3 on top for the Jack | The Sleeve-Lock A-Frame Trailer Coupler - Flip Latch - Black - 2-5/16"...
Is There A Way To Unmarry The Edge CTS3 Tuner From Your Vehicle
How to unmary from my truck | I talked with the vendor about unmarrying the Edge CTS3 Tuner. You will need to go into the tune menu and look for 'return to stock' or 'backup'. This will walk you through the necessary steps to return your truck...
Replacement Jack for Shorelandr Trailer with Bulldog 130 Series Jack
Looking for a replacement jack for this shoreland trailer, Jack is bulldog 130 series pics attached this bolted on and dont want to modify trailer hope you can help. | While we do have similar swivel jacks that can be used on your boat trailer...
Can a 10K Bulldog Drop Leg Trailer Jack be Trimmed to be Shorter
Purchased a pair of 10,000 lb Bulldog jacks to stabilize a trailer when loading. The jacks are of a drop leg style. Theyre too long for the application and it appears there is no shorter option. Is it possible to disassemble the jack and...
Inside and Outside Diameters of Bulldog # BD500212 Replacement Gear Set
Hi, Im looking for some specs on product code BD500212. Wondering what the inside and outside diameter is on both gears? Thanks | The # BD500212 Bulldog Replacement Sidewind Jack Gears are compatible with Bulldog-branded sidewind 12K capacity...
Usable Length of Available 9/16-Inch Diameter Pull Pins
Is this pin available with a 4 inch useable length? | We offer three 9/16-inch diameter pull pins including the Bulldog # BD500243 which has a usable length of 2-1/2-inches. Bulldog part # BD500338 has a usable length of 2-3/4-inches and part...
Which Jack Goes With Bulldog Square Jack BD183749 To Be Used As Landing Gear?
what is the part # for slave Jack when using the BD 183749 as the drive? | We have exactly what you are looking for. The correct jack to pair with the Bulldog 2-Speed Square Jack - Drop Leg w/ Non-Spring Return - 26" Lift - 25,000 lbs # BD183749...
Replacement Motor Brush Springs for Lippert 181794 Powered Trailer Jack
I have a model 181794 power tongue jack that one of the springs that holds the brushes down broke. Are there springs available to replace them? | Unfortunately, Lippert doesn't offer internal replacement parts for their 181794 Power Trailer...
Availability Of Replacement Handle For Bulldog Square Swivel Jack W/Round Pipe Mount BD190708
I need a new handle for this jack. Can you provide? Thanks | We have exactly what you are looking for! I reached out to my contact at Bulldog and the correct replacement handle for the Bulldog Square Swivel Jack w/ Round Pipe Mount - Drop...
Can Leg on 4000 lb Powered Trailer Jack Be Replaced
I bent the leg on my 4000 pound electric jack can I replace it | If it's the drop leg like # BD500190 that's bent, you certainly can replace it if it's not bent to the point where you can pull the pin and slide the drop leg out. The # BD500190...
Filter Your Search
Contact and Help