Availability Of Replacement Handle For Bulldog Square Swivel Jack W/Round Pipe Mount BD190708

Question

Question:

I need a new handle for this jack. Can you provide? Thanks

asked by: Andrew E

0

Expert Reply:

We have exactly what you are looking for!

I reached out to my contact at Bulldog and the correct replacement handle for the Bulldog Square Swivel Jack w/ Round Pipe Mount - Drop Leg - Topwind - 28-1/2" Lift - 5,000 lbs # BD190708 you have is either the # BD105212701 which will be 1" shorter than your current handle, or you can use the # BD500344 which will be 2" longer if you have the available space.

expert reply by: Samuel C

0

Answer 1

The Replacement Topwind Handle for Bulldog Topwind Jacks #BD105212701 has a 3/4" shaft diameter, so it might be what you're looking for.

view full answer...

Answer 2

The overall length of the Replacement Topwind Handle w/ Claw Knob for etrailer and Ram Square, Direct Weld Jacks #TJD-7000-HD is 10-1/2 inches. The center to center length is 9 inches. I've attached a photo to assist.

view full answer...

Answer 3

The bolt included with the Replacement Topwind Knob Handle for Ram Jacks #TJPB-HD is 6mm x 1.00 course threaded bolt. The length from the bottom of the head of the bolt to the tip is 1.25" with 7/8" of it not having threads.

view full answer...

Answer 4

Yes, we do carry the correct replacement handle for the Square Direct Weld 7K Jack part #TJD-8000. It's the Replacement Topwind Handle part #TJD-7000-HD which is exactly what the jack would have come with when new and it's an easy bolt-on…

view full answer...

Answer 5

Hey Kelly yes, the handle diameter is the same for both #TJPB-HD and #TJD-7000-HD and the mount for both is the same size as well. The only difference between the two handles aside from the length are the jacks they fit. The Replacement Topwind Knob…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Availability Of Replacement Handle For Bulldog Square Swivel Jack W/Round Pipe Mount BD190708

Continue Researching