Correct Slipper Spring for my 16 ft. Aluminum Jon Boat Trailer
I have an old boat trailer with 1.5” dia axle that needs new springs. There are no ID numbers anywhere on the trailer or axle, but the old springs are 4 leaf springs. The trailer is carrying a 16 ft aluminum Jon boat made of 1/8” aluminum. Would...
Picking Between 27 inch and 25-1/8 inch Long Leaf Spring for Trailer
Looking to purchase leaf springs for a diy utility trailer with 3500# axle. Is there any reason not to go with the longer 27” leaf springs compared to the 25.125”. Purchasing new hang kit as well, suggestions? | There wouldn't be a noticeable...
Availability of Slipper Spring to Replace 26-1/2 inch Spring
Hello I’m working on a 2005 Fleetwood Resolute pop up camper. I took the slipper leaf springs out and looking to replace them. They are 26 1/2” from center eye to end of slipper and 1 3/4” wide. They are radius end 3 leaf slipper springs. Do...
How Far Apart Should Hangers Be on My Custom Built Trailer With 27" Leaf Springs?
What hanger kit do you recommend for leaf spring SP-210275 27” for use with a single axle 4” axle, 3500 lbs, 2 3/8 tube mounted over the spring, and what distance do you recommend between the hangars? This is for a trailer I am building. Thank...
Tandem Slipper Spring Hanger Dimensions
I would like to know the hanger spacing for tandem axle kit AP216-H238 with 13 1/8 equillizer 4000 lbs 4 leaf slipper springs Thanks | When you use the Tandem-Axle Trailer Hanger Kit # AP216-H238 with the 4 Leaf Slipper springs part # SP-230275...
How to Lift a Trailer w/ Axles Below the Leaf Springs
I would like to lift my camper 1.5 to 2 inches. Its a 2017 coleman lantern 262bh. Tandem axle. Lippert 3500lb axles 2-3/8 tube. The leaf springs are already on top of the axles. Do you have any recommendations without having to do any welding...
Are Trailer Spring Seats Needed for Square Axles with Leaf Springs?
Im replacing my square boat trailer axle.the one i have know has no spring seats it sits right on the leaf springs.i noticed most square axle fully assemble axles which i want has spring seats.this is a tandem axle trailer.im not replacing the...
Replacement Leaf Spring for 7k Axle that is 26-3/4 inches Long
Good afternoon, I have some leaf springs from my trailer and Im trying to figure out which leafs I can use to replace them. The trailer is a 1986 so there isnt much info left on it anywhere. The MAX CAP for the axles is 12,000lbs, they are...
Size of Bushing Inner Diameter in Slipper Leaf Springs
I need to replace the springs on my small utility trailer. P/N 177275 appears to be the correct replacement with the exception of bushing inside diameter. My trailer uses 1/2 inch ID hanger bolt hardware. Solution? | Replacement trailer leaf...
Replacement Slipper Spring for Boat Trailer 1000-lb Axle
The spring that I took off of the trailer measures about 25 and 1/4 inch. and 1 and3/4 in. wide, The bolt hole measures 1/2 inch had a 1/2 inch bolt. This looks like the 24 and 1/4 inch slipper spring for 1000 lb axle. It says that the bolt...
Determining Which Leaf Springs Fit A Continental AWC11e Trailer
Hello, I am currently trying to find leaf spring replacements for my Continental AWC11e Trailer. These are the ones that I think will fit, but the springs on my current trailer are stacked 4 high and are flat at the bottom, not rounded off....
Slipper Spring Recommendation for Cox Boat Trailer with Springs that are 24-1/2 inches Long
Im repairing my Dads Cox boat trailer. I need to replace the leaf springs. They are app. 24.5in from pin to the end and this model has a hook end on it. Its a 4 leaf spring with about 4 inch lift. Do you have a compatible spring for this...
Recommended Lift Kit For Trailer Tire Fender Clearance
I am adding new leaf springs and axle to my 2,000lb trailer. Would like to go from my current 8” tire to a 12” tire. By doing that with the current configuration I will only have 1” clearance between the top of the tire and the inside of my...
Difference Between Measurements on 3,500 lb Double Eye Leaf Spring
Is the axle mounting position directly in the center of this leaf spring? The measurements for A and B are 13 1/2 inch and 14 inch and I wasnt sure if that was the measurement from eye to center in each side. | The axle should mount over the...
Recommended Replacement Slipper Spring Leaf Springs
I am changing leave springs on my boat trailer on side is closed one is open I measured from bolt to bolt center while leave spring is on trailer to rusty might fall apart if I take off to measure because of so much rust but it measured 23 inches...
Recommended Trailer Suspension Enhancement To Keep From Bottoming Out
I have a 1966 globestar camper trailer.the GVW on reg says that it weighs 2250 pounds.As I am towing down the road she bottoms out.As far as I know that the leaf springs have never been changed not scenes Ive owned it. I guess my question is...
Replacement Slipper Springs to Replace 32 Inch Long Springs
My boat trailer has slipper springs. 1.75 inches wide. 32 inches long. Radius. Radius top contacts trailer at 28 inches. your closest spring is 30 long with no radius. Do you have a product I can use? | The 30 inch slipper springs we carry...
Determining Correct Hanger Spacing For Installing Single-Axle Hanger Kit APS4 W/ 24-7/8" Leaf Spring
Hi, Can you tell me the proper mounting dimension for your APS4 leaf spring hanger kit with SP-222275 leaf spring? I have researched online and found a few conflicting dimensions. Thanks | The 6-Leaf Double-Eye Spring for 5,300-lb Trailer...
Need a 3-Leaf Slipper Spring Kit for my Boat Trailer with 2 Inch Square Axles
Do you sell a complete kit for my springs on my boat trailer. I have a 2 in. Square axle. There are two leaf slipper springs. 1-3/4 wide. What I like to do is put 3 leaf springs in and do the two u bolts preside like your video. I currently...
Replacement Springs for a Utility Trailer with 2,000 Pound Axle
The hanger spacing center to center is 29 1/2 inches. 2000 lb utility trailer, 1 3/4 inch axle with 1 3/4 inch wide ssprings. What length spring would I use? 29.70? No year or info on trailer. It is a 6 ft. X 8 ft. | The typical hanger spacing...
1,000 lb Slipper Spring Recommendation for a Motorcycle Trailer
Can a leaf be taken out to make the spring softer? The springs would be going on a small town behind motorcycle trailer. I am replacing the single leaf slipper spings and do not need 1000# springs. #500 would be great for what I need. | The...
Square U-Bolt Kit for Mounting Leaf Springs SP-177275 to 1-1/2 Inch Square Axle
I am replacing the leaf springs on an old boat trailer. I have selected Slipper leaf springs 1 -3/4 inch SP177275 but I am uncertain on U-Bolt selection. A mounting plate is already welded to the 1 1/2 inch square axle. I have selected...
Recommended Jet Ski Trailer Leaf Spring U-Bolt Mounting Kit for 1-1/2 Inch Square Axle
Hello , I am looking to replace both my leaf springs on my jet ski trailer I determined that SP-113275 will fit , but I cant seem to find a square U bolt that will. My axle is 1-1/2x1-1/2 and the square you bolt is about 4 inches long and the...
What Size Bolt Is Needed for the 4-Leaf Slipper Spring 3,700 Lb with Flat End
looking at item # sp-040275can you tell me if the eye hole will accepta 3/4 inch bolt? | The 4-Leaf Slipper Spring w/ Flat End part # SP-040275 is designed for 9/16" bolts only, the Spring-Eye Bolt with Locknut for Slipper Springs part # 166079....
Filter Your Search
Contact and Help