Recommended Ladder Rack for 1976 Chevrolet C10
Hi i have a Chevrolet Pick up C10, and im not shure wich size of the race should take. the bed on the pick up is 245cm long / 175cm large. Do i need to take a 6 foot or a 8 foot rac? thanks by advance for your help. | Based on the measurements...
Comparing etrailer Electric Trailer Brake Assemblies to Dexter Brakes
I have a 14k trailer has dexter axles and one axle has the self adjust dexter brakes and I want to add brakes to the second axle. I am wondering if there is any noticeable difference between the dexter brand brakes and the etrailer brand brakes....
Custom Fit 5th Wheel Rails And In-Bed 7-Way For A 1976 Ford F-250
Hi all, very new to towing and I’m considering a 5th wheel hitch for towing a dump trailer on my old beast of a work truck. 76 f250 camper special, 460 with the heavier springs and rear axle. looking at the Reese 16k and it appears as though...
Hitch Recommendation for a 1976 Ford F150 with a Deep Drop Bumper
what is a roll pan bumper? I have sent a photo of mine. is this a bumper. it doesnt measure 10 inches. | A roll pan bumper is a bumper that basically makes the rear bumper look as if it does not stick out further than the rest of the truck...
Weight Capacity of Redline HP344G Greasable Hinges
I am building a tilt up trailer ramp/gate that could potentially haul my 4500lb truck would 2 of these hinges work? The gate will be 88inx48in all 2in tube as well as angle | According to Redline, the # HP344G hinges don't carry a weight rating,...
Measurements of etrailer Hitch for 1976 K10 Pickup
What are the dimension of this hitch? I am looking for top of the mounting plate to the top of the hitch sleeve for example the Curt 13028 is 4.5-5inch depending on where you measure on the 2inch shaft? I am also looking for the length from...
Custom Snow Plow Mount for 1976 Ford F-250
Do you have a custom plow mount that will fit a 1976 Ford F-250 4x4? I have looked elsewhere and and have had no luck. | You're in luck because there are custom mounting brackets for a snow plow that fit your 1976 Ford F-250 (so long as it is...
Is Drilling Required to Install B&W Trailer Hitch Receiver # BWHDRH25122 on 1976 Dodge Truck
It states that no drilling is required, is that really true? When I searched this part number many other makes come up attached to it. So just want to know if it is a true no drilling required or not. Thanks | To install the B&W Heavy-Duty...
Specs for the Air Lift Ride Control Air Helper Springs # AL59561
Can you provide the following specs on this air bag? Inflation port size: Compressed height: Extended height: Ride height range: Maximum diameter: Maximum PSI: | The Air Lift Ride Control Air Helper Springs # AL59561 has the following specs: Inflation...
Front Hitch For A 1976 International Scout II
when I enter vehicle infor #C31083 comes up for front hitch set up for 1976 IH Scout. Does it indeed fit our vehicle and what class is this hitch? | The only hitch I have for you is going to be a rear class III hitch # 13580. The # C31083 front...
What Hitch for 1976 Chevy Pickup with 8ft. Bed and What Installation Is Involved
Hi: Is this a direct bolt on with no modifications to my truck? Will I have to drill holes in my frame? Will I have to remove the bed to put it on? Will it clear where my spare tire is I have the standard factory spare mounting which is between...
Trailer Hitch Recommendation for a 1976 Ford F-Series Truck with 4 Wheel Drive
i need to know it this will fit my 1976 ford highboy 4x4 i think i have the narrow frame and will it work with a weight distributive type ball mount? | A high boy is a generic term used to encompass all Ford F-250 4x4 trucks from the late 1960s...
Replacement Roof Vent Lid Recommendation for 1993 Lance Squire 4000
Trying to get a vent lid for our 1993 Lance Squire 4000 9foot 4. Its looks to be the 14x14 but the hinge pins everyone sells opposite of what I have. The hinges on mine are small, large, large center small, large. Most I see are for four...
Availability Of Trailer Hitch Receiver For 1973 Jeep CJ-5 V8
Why wont this fit a 73 CJ-5 V-8? other hitches go for all cj5 no matter what year they are. Thanks, Steve | The reason the Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" # 13412 you were looking at will not fit a 1973 Jeep CJ-5 is...
Trailer Hitch for 1976 Chevy C/K Series Stepside With Short Bed
HI, I have a 1976 Chevy k10 short bed stepside. I need a hitch that does not interfere with the spare tire mounted under the truck. Thanks | The trailer hitch that fits your 1976 Chevy K10 short bed stepside, and will not interfere with your...
Available Solution to Add a Front Mounted Hitch to a 1976 GMC Motorhome
I need a 2 receiver that will fit the FRONT of my 1976 GMC Motorhome. Suggestions? Thanks | I may have a solution for you, but there is not a custom fit hitch for this vehicle so it may require some fabrication. With that said, you may be...
What Secures Rampage Safari Island Topper to 1976 Ford Bronco
I have a 76 Bronco with family roll cage- pipes from windshield to behind rear seat. Does this item get pulled over the cage and then what secures it ? Is this item like a full bikini top , or does it have something for sides and rear ? Any...
What is the Largest Wheel Strap for the Demco Kar Kaddy SS Tow Dolly Part 9713045
1976 Jeep CJ7 with 31X10.5X15 Cooper Discoverer tires. The Dolly is a Kar Kaddy SS. What wheel strap do you recommend. Will DM03528-93 work? Thanks | Yes, the Replacement 3-Point Large Wheel Tie-Down Strap part # DM03528-93 will allow you to...
Is There a Trailer Hitch Receiver Available For a 1976 Lincoln Mark IV?
I am looking for receiver only for under rear bumper of my 1976 Lincoln Mark IV | While we currently do not carry a custom fit receiver for your 1976 Lincoln Mark IV you may be able to have one fabricated using our Weld-On Receiver # E17. You...
Trailer Hitch Recommendation with High Capacity for 1976 Chevy K20 Truck
Im looking for a receiver for my 1976 Chevy k20 3/4 ton class 3 factory style replacement with the most weight rating and whats tongue load mean ? | The highest capacity hitch we have for your 1976 Chevy K20 is the Draw Tite part # 41947 which...
How Can You Tell Which Size Eye Bolt Fits Into Yakima HD Crossbars?
It seems that the anima eye bolts fit most t slot rack and bars that said the $28 I have aice for 2 is a bit steep - they also are steel and not stainless - I have seen other eye bolts for T slots online - is there a specific siz needed for...
What Gauge Are The Wires Of The EZ Connector Magnetic 7-way Connector 319-S7-05?
Please confirm the wire gauge on the EZ 7 way socket, are they all the same? As opposed to the Fifth wheel model that lists the various colors and corresponding gauge. | The wires on the EZ Connector Magnetic 7-Way Trailer Connector with Watertight...
Overall Length of the Aries Round Nerf Bars # AA204040-2
What is length front to back ? | From front to back the Aries steps part # AA204040-2 measures 66-1/2 inches. |
Brake Controller Recommendation for a 1976 Dodge RM300
My question is, what type of brake controller do I need for a 1976 DODGE RM300 RV CHASIS? Since the vehicle isnt setup like a newer plug an play vehicle, is there a certain type of controller I need. Thanks for your time! | For a brake controller...
Filter Your Search
Contact and Help