!Liberty Travel Trailer  x   >   !Comet Mini Travel Trailer  x   >   !Camper  x   >   DeeMaxx  x   >  

My trailer has 3500lb axles and the 6 bolt pattern, will this work? | I do have an option for you but if you want to switch to disc brakes, you'd need to pick out new wheels as they don't offer any brakes kits for a 3,500 lb axle with a 6 on...

Can you reposition the brake line attachment on the stainless caliper that comes with this kit without it leaking at 1600 psi? In my case, I either need to tighten the fitting 270 degrees or loosen it 45 degrees so it points to the rear of the...

What type of sealant should be used to install this fitting into the caliper? Not sure if it requires white teflon tape or some type of pipe dope. Thanks | You only want to use a thread sealant like the Permatex 59214 on the NPT side of the...

I would like to know if Item # DE62FR Deemax brake kit will fit on my boat trailer. I have an ez loader trailer with axle # 250-024287-10 and oil hub kit not the short hub # 300-034857. The axle and hub kit are already on the trailer and I plan...

I purchased idler hubs AKIHUB-865-7-2-EZ-K and the Hydrastar brake kit with the slip-over rotors HSE7K-T1SO. The problem Im having is that the studs on the hubs are too short due to the thickness of the rotors my lugs only thread about halfway...

I have a Lakota LQ horse trailer and looking to replace the lug nuts with ones that DO NOT have decorative caps on them. The size is 9/16 and I need 32 lug nuts. Do you carry these? | Hi Kat, Yes, for a 9/16" wheel stud I recommend the DeeMaxx...

Do you. Have SS backed pads for DBSO-6K-MAXX 6000 pound system how much are they …thanks | You will need the DeeMaxx Ceramic Brake Pads with Stainless Steel Back Plates # DE98VR to fit the DeeMaxx Disc Brake Kit DBSO-6K-MAXX # DE82FR. We also...

Does the caliper on a boat trailer need to be replace if it’s functioning properly despite the dust cover boots having a crack in it? I am serving my boat trailer clean, inspect and repack bearings and noticed my caliper’s dust boot is cracked-...

Do you guys carry torsion arm vault hub assembly for a 2014 E Z load boat trailer? | To find your exact hubs we will need either the numbers off the bearings and grease seals to determine the spindle size or the diameter of the different landings...

I got a big tex trailler 2006 with two axle but dual so 8 tires im traing to buy the brake disc sistem but i dont know wichone fix in my trailler this the vin of mu trailler XXXXXXXXXXXXXXXXX | I can tell you how to determine the correct disc...

What is the maxx coating on this and why is part of it stainless and part of it maxx? | The DeeMaxx Disc Brake Kit - Maxx Coat/Stainless - 3,500 lbs # DE46YR uses stainless steel calipers and a Maxx coating on the hub and rotor. This Maxx coating...

What's with the holes in this? | The holes in the DeeMaxx 10" Hub-and-Rotor Assembly # DE49VR are designed to avoid water pooling into that part of the assembly. I wouldn't say that pooling what is a massive issue, but just the fact that DeeMaxx...

I have a 2014 Wesco Trailer Model B-AL-2036 @4200 GVWR, will these brakes work with that trailer? If not, do you have a recommendation of ones that will. Thanks Joe | Hey Joe, the DeMaxx Disc Brake Kit part # DE82FR will work on your Wesco...

Do you stock the triple lip inner seal dexter p/n 010-11088 I need 2 | Hey Brandon, Yes, we do offer the 010-11088 under the Grease Seal Kit- Triple Lip # DX49CR. This comes in a quantity of two seals per kit. |

these seem very similar to the demco 03927. Do you know if they will fit in place of a demco 10inch rotor? | Although they do look similar, they will not work in place of your Demco 10" brake rotors. Instead, you'd need to use the Replacement...

Hello! What is the orifice size of the female break line fitting on the back of the break lock out selonoid? Many thanks! | Hey David, The Dexter DX7.5L A-60 Brake Actuator w Electric Lockout # DX56FR accepts brake lines with 3/16" male inverted...

What size of stud do you need for a DE93GR lug nut? | Hey Natah, thanks for reaching out! The DeeMaxx Trailer Wheel Lug Nut # DE93GR is compatible with 1/2"-20 wheel studs. This is a standard size for 1/2" studs so if that's what you have...

I am looking for some 1/2 x 20 lug studs. the knurled part is .500 diameter. just a bit under 2 long and have a 1/4 thick round top that is about .750 in diameter with a side cut off so it is not completely round. I could take the side off myself...

Im interested in these hubs, but I want to keep spare parts on hand in case theyre needed. I see the bearing and seal part numbers, whats the part number for replacement wheel studs? Thanks! | To replace the studs on the DeeMaxx Trailer Idler...

In the description, its mentioned that these work with slip-on disc brake rotors. Whats the part number for the rotor? | The DeeMaxx Trailer Idler Hub # DE36VR is designed to fit with DeeMaxx 10" Rotor with Maxx Coating # DE47VR or Stainless...

Can it be machined? Whats the minimum rotor thickness? | I just checked with DeeMax and the rotor part # DE69VR can be machined and the minimum thickness is .815 inch. |

I have 7000 lb tandem axles w/ elec drum brakes. Thinking of converting to disc. Is the hydrastar brakes and actuator equal, or better in quality to the kodiak disc brakes. Does the hydrastar work w/ my 2023 f350 brake controller or is some...

Will this work with vault service kit? | Yes, the DeeMaxx Disc Brake Assembly # DE89YR will work with the Dexter Vault service kit. |

Will it fit on 2021 nitro z20 bass boat | The DeeMaxx Disc Brake Caliper item # DE86VR is not going to fit on 2021 Nitro Z20 bass boat but so long as you have a mounting bracket for disc brakes it will fit on your trailer. These are pretty universal....