Result: knobs

Have power at the controller, no lights at the knob. | Have power at the controller, no lights at the knob. | I would start by using a hook probe tester like the # PTW2993 to check and see if you're getting a power feed on the...

Is this knob the ground connection or what is the difference between the adapators that do or dont have this knob? | I have a 2003 4 Runner with tow package the factory hitch connection is 7 flat. I have a...

To level the sensor, you will set the power knob to maximum by fully rotating it clockwise (with the trailer connected). | Light on controller goes from green to a light green. No assist. Will not adjust with the riflght diel....

I made you a short video that shows how to replace the knob provided that the little tabs on the back of the knob or where they mount are not damaged. | While installing and checking operation, as I activated...

You are going to want the Redarc Tow-Pro Liberty Brake Controller w/ Universal Wiring Harness - Dash Knob - Proportional # RED52VR, don't forget to grab a Universal Mounting Panel for Redarc Tow-Pro Trailer Brake Controller Control Knob # 331-TPSI-001 for one of those empty spots on your dash. |

As a test I held the P2 at no upward angle in my hand and applied the manual power knob, with no increase / improvement in braking power. | Hello eTrailer. I recently installed the Prodigy P2 Brake Controller on my 2017...

Check to be sure that the power knob is not set all the way to the lowest position. | I just hook up a pilot controller and if i hit the break pedal the dot in the middle lights up, but if i use the button on the controller...

Now for installing the knob of the controller you will need to pick a spot that you have at least 3/4" clearance for the knob, and 1-3/4" space behind the location for the back part of the knob to have enough clearance. |

It has a manual slide, a power knob on the right and another knob on the left. | Its a Journey model # 527408045 approx. 7 yrs. old. I lost my manual and want to set it up for a new trailer. Is there a manual...

Also no lights on the control knob! | How do you make the brake controller think it is connected to a trailer with brakes? Just to make the unit light up. I have no lights on the control knob. I do lights on the tester for...

Then rotate the Level Knob clockwise until you see a shade of orange on the light. | I have the four wires hooked up, have power to the controller. But it doesnt go from green to orange/red when I try leveling the sensor....

The main unit measures 3-3/8" long x 3-15/16" wide x 1-1/8" tall and the control knob measures 2-3/8" long x 3/4" wide x 7/8" tall. | Im interested in Redarc Tow-Pro Elite # RED44FR because the control can be hidden and placed...

This is with the power knob all the way clockwise. Thanks | My green light looks like its on with trailer disconnected but when my trailer is connected the green light is much brighter. Also, I was trying to adjust my level...

WHEN CONNECTED TO VAN GREEN LIGHT IS ON WHEN EMEGENCY BRAKE IS APPLIED ,LIGHT TURNS RED WHEN FOOT BRAKE IS APPLIED LIGHT STAYS GREEN NO MATTER WHERE THE POWER KNOB OR LEVEL KNOB IS. WHAT IS THE PROBLEM? | WHEN...

I see that the Redarc has a separate adjustment knob that you mount wherever desired. The knob then plugs into the control box and the Ranger factory wiring gets spliced into a 4-wire pigtail that then plugs into the controller to complete the installation. |

When I attach my trailer to my vehicle the control knob of the Redarc glows blue as it should. When I apply the breaks the color of the knob fades to purple then green which most closely resembles The LED Flashes an unusual colour sequence randomly whilst braking. |

What position should the power knob be in. I think I may have turned it off. I do not have a green power light showing anymore!! | What position should the power knob be in. I think I may have turned it off. I do not have a...

When that knob is not adjusting just right the controller will not function properly. | I have had this controller on my truck for three years with absolutely no problems. Yesterday I hooked up my 20foot enclosed trailer and...

Performance Tool doesn't have any maintenance instructions for the Electric Blower # PTW50061 in the manual but when I reached out to my contact they suggested the following procedure: 1. Plug in 2. Turn knob to desired speed 3. Unplug and clean with a damp rag 4. |

I like this brake controller because the main unit mounts behind the dash so the only thing taking up space in the cab is the control knob. The knob controls the braking power and acts as the manual override....

The lever below manuel knob can be activated and braking does occurs and the display reads out the proportion of braking. | Have installed a Prodigy P2 that is used on two different vehicles, 2001 Isuzu NPR with GMC gas engine,...

Both the soft bristles and microfiber ends get into tight slats without bending or damaging them, and is great for knobs and seams. I’ve even seen folks use it on blinds or other random hard-to-clean areas. | Could I use the...

Set the power output to the maximum 13 volts using the power knob and activate the manual knob. Use a volt meter to test the output on the blue wire. | I have installed the Prodigy 90185 into my 2007 Honda...

While holding the brakes, rotate the power knob back until the light changes from green to red. | We have a 2004 Chevy Silverado with the Voyager brake controller. We have used it for about 5 years now. Just yesterday, when...