Result: Boat Loading Guide

Hey Chad, There unfortunately isn't a guide to tell us the correct bearings and seals for your Load Rite boat trailer so you'll need to remove the hub and check for the part numbers or measure the spindle and hub bore hole. |

Another option is to use the CE Smith Post-Style Guide-Ons with LED Lights for Boat Trailers # CE27740 which will allow you to see the empty boat trailer and also help as you load your boat onto your trailer in the dawn or dusk timeframes. |

I have a 2015 load rite tandem boat trailer. Current surge setup with 12 6 lug rotors. | I have a 2015 load rite tandem boat trailer. Current surge setup with 12 6 lug rotors. Im wanting to replace all 4...

Hi Doug, There unfortunately isn't a guide to tell us what hubs were used on your Wesco boat trailer so I'd need you to either check for the bearing and grease seal part numbers or measure your spindle at points B, C, and D with a caliper # PTW80157 so I can see what bearings and seals would fit the spindle. |

Looking for a bearing kit for a 1996 Load Right boat trailer. I understand that there might be no kit available. | Looking for a bearing kit for a 1996 Load Right boat trailer. I understand that there might...

I have a round 7 pin coming from the Tohoe then a connector that takes a 5 pin coming off of the boat trailer. Do you have a diagram to show how to wire the 2 6 back up light I will install on the back of the trailer for backing the boat in...

I just got a 1988 Cox tandem axle boat trailer with boat, but it is not equipped with brakes. | I just got a 1988 Cox tandem axle boat trailer with boat, but it is not equipped with brakes. The four hole backing...

Hello, I am looking for a replacement hub kit for 1998 Load Rite boat trailer. Known trailer specifications: Model 16-1501R Hull Length 15’-17’ Caring Capacity 1500 Tires 4.80 12C Approximate Weight 289 |...

I live in a boating community and will be storing a 24.5 foot Nauticstar that weighs approximately 3400 pounds on a secondary boat drive way that is slightly sloped 8-10 inches sloped side-to-side where the boat is kept. |

Hi I have an ez load trailer, single axel that has a sea pro 190 boat on it. 18.5foot boat. 14inch wheels. | Hi I have an ez load trailer, single axel that has a sea pro 190 boat on it. 18.5foot...

To answer your first question in regards to the Viking Solutions Rack Jack Magnum Hoist with Winch, # 310-VMH001, and "...pulling the supported load ... rather than vertically...". While an 85 lb. load may be successful, it has not been tested for that and is not the intended use. |

Im looking to purchase new hub assembly for my boat trailer. its 5 bolt its measures 4 5/8 center to center the load rating for the trailer is 2970 lbs. the boat weights 1600 lbs. it is a galvanized trailer 2008. could you make some recommendations, so I purchase the correct assembly. |

Im trying to find disc brake kits for a Load rite 5-star Boat trailer. Metal Tag reads 49649 Tongue Tag B092191269 TDE 1146469 6 Bolt 5 1/2 dia. 12 inch rotors | Im trying to find disc brake kits for a Load...

Gross rating 1990lb max load capacity 1490lb. | I have a TRAILSTAR trailer that came with my Grizzly 18ft boat. I want to buy hub kits but dont know if the spindle is 1 inch or 1 1/16 inch. The trailer type is U-1813 manufactured...

Lastly keep in mind that depending on the weight of your trailer when it is loaded with your boat, you may legally be required to keep brakes. | Hi, I am removing the brake drum assembly from my 19 foot boat...

Hello weve installed a new controller and new complete electric assemblies on our boat trailer and new wire from assembly to assembly and to the junction box on trailer and a new pig tail to the truck from the junction box on the trailer the brakes hardly work when dry after we load the boat and head home they will work good enough to stop the truck and trailer dead in its tracks as soon as they dry out back to nearly no brakes I dont understand what is happening we have great voltage on the shop floor and the same readings at the boat launch after coming out of the water |

Do you have enough info to guide me to correct hubs? | I have a ranger trail 2003 model r61 trailer with cool hubs. I want to replace both hubs. Do you have enough info to guide me to correct hubs? | From our experience the...

need a hitch and wiring. boats got a 5flat | got rid of my f250 and got a 2018 flex. hoping i can still tow my boat or im going to drive the flex into the lake. need a hitch and wiring. boats got a 5flat | From what I found...

I have a 54’ gooseneck boat trailer and when I apply the brake foot pedal no brakes and when I apply by using the brake controller no brakes. | I have a 54’ gooseneck boat trailer and when I apply the brake foot pedal no brakes...

Note: My trailer has six lights: 1 above each wheel, 1 at each back corner low and 1 on each side set on poles to guide the boat into the trailer if the trailer is underwater. | I need to rewire a boat trailer...

Hi I have a similar problem to this fellow here I have a trailer and boat that are about 10,000 - 12,000 lbs the boat is 9,500lbs I am trying to lift the trailers off the tires. | Hi I have a similar problem...

Can you use electric brakes on a boat trailer, being it will be under water at times with launching and loading? | Can you use electric brakes on a boat trailer, being it will be under water at times with launching...

I am looking to replace both hubs on a 1999 Load Rite 161250L boat trailer. Load Rite says they believe it has 1.06 in straight spindles. | I am looking to replace both hubs on a 1999 Load...

Hey guys, I am looking for replacement hubs for my 2005 Four Winns Trailer. The trailer model number is DO190VT. Do you know if I need the same part number AKIHUB-655-6-EZ-K you have recommended for a 2004 model trailer? Cheers | Hey Paul, There...