Rabbit Pickup x > Rampage x > Rabbit x > Freestar x >

Result:

Articles

Tow Bar for 1981 Volkswagen Rabbit Pickup

What tow bar will hook up to a Volkswagen rabbit truck bumper, I need one that is 31 inches | Hi Andrew; are you saying you need the arms to be 31" apart? The Curt Adjustable Tow Bar # C19745 you were looking at has an adjustable arm width from...

Troubleshooting Running Light Circuit of Curt Trailer Wiring # C56673 Not Functioning

I connected the wiring harness to the factory connection on my 2006 Ford Freestar, installed the relays and fuses and then connected the trailer. The running lights did not work, all of the lights flashed when the right turn signal was operated,...

Does The GE Appliances RV Refrigerator GE58FR Come With A Mounting Bracket?

Does this with mounting brackets? | Hello Raymond, thanks for reaching out. The mounting brackets are not included with the GE Appliances RV Refrigerator # GE58FR. It requires a GE approved top bracket part BMT-GPV10. This is not something we...

Installation Instructions for Wiring a 2008 Volkswagen Rabbit to Tow a Trailer

My question is about the electical hook-up. Can I splice a 4-flat connector directly into the wiring harness, or do I need some kind of powered module dure to the fact that it6 haqs LED lights? | Due to the MX (Multi-Plexed) wiring system on...

What is the Battery Life for Hopkins Wireless Magnetic Tow Lights

What is range of battery life for these lights? The check battery level indicator light every 2 hours statement has me concerned. I drive for much longer stretches than that and dont wish to carry excessive spare AAs or replace them every couple...

Why is a Stabilizing Strap Recommended on Curt Hitches and what is Meant by Non-Trailer Load

What is meant by stabilizing straps for non-trailer loads? | Non-trailer loads are hitch accessories like bike racks and cargo carriers. Basically anything that is not a trailer that you could put on a hitch. Curt recommends you use a Curt Trailer...

Trailer Wiring with Relays Recommendation for a 2004 Ford Freestar

I have a 2004 Ford Freestar with the factory towing package, however, I am missing the three relays found under the hood. Can you sell me the three relays alone without the plug or wiring harness? | The only way I can recommend for you to get...

Replacement Jack For 2001 Stratos Bass Boat Trailer

I have a 2001 Stratos Bass boat with a Fulton center bolt swivel jack onto a welded plate on the trailer. I would like to upgrade to the Fulton F2. My holes on the plate are 3X3 on center. Will the F2 work? Can I send you picture? Thank You...

Will Bulldog Powered Drive Kit Fit a Fulton 12K Magnum Jack

Is this Bull Dog Powered Drive kit compatible with a Fulton Magnum Series Heavy Duty 12,000 Lb. Capacity Leg jack. Use is horse trailer with living quarters. Currently manual crank. | Bulldog Powered-Drive Kit # BD1824200100 comes with the...

Trailer Wiring Plug Location to Install Wiring Harness # C55673 on a 2006 Ford Freestar

Hi, My van is 2006 Ford Freestar SE. I bought kit #56673. I could not find the minivans connector to plug in with new #56673. Where is it? Thank you in advance. | The plug on a 2006 Ford Freestar to install the Trailer Wiring Harness,...

Replacing Swivel Jack on Coleman Fleetwood Pop-Up Trailer

I have swivel jack on passenger side of tounge. Looks like in order to add my fastway weight distrbution with sway control.... trunnion style for 800lbs.... I will need to move my swivel jack.... .. On the inside of thea frame of the tounge...

Diagnosing and Repairing Wiring Problem on Trailer Towed by 2006 Ford Freestar

My son-in-law purchased a hitch and wiring adapter from you for his 2006 Ford Freestar. Installed adapter, relays and fuses attached to trailer lights and observed these symptoms, with vehicle lights off: 1 press car brake: trailer running...

Floormats For 2006 Ford E450 Motorhome

Looking for floor mats for my 2006 E450 motorhome | Yes, we do. These are a confirmed fit # WTW51 for your E450 motorhome. If you wanted tan # WTW51TN or grey # WTW51GR we have them too! |

Is Trimming of the Foam Absorber Required for the Curt Hitch On a 2010 Mini Cooper Convertible

have a question about hitch and hard form . I removed the bumper today for preparation for hitch installation. The bumper has the hard foam but it is wedge between the front and back metal bumper with a full metal back hard foam cannot be...

Dimensions of Replacement Right Rear Leg for Lippert Ground Control Leveling System

Hello What is the overall dimensions of this model? Thank you for your time and have a great weekend. | The Replacement Right Rear Leg for Lippert Components Ground Control 3.0 Electric Leveling System- Qty 1 # LC344792 has the following dimensions:\ 99...

How to Prevent Exhaust Components from Contacting the Trailer Hitch

I purchased the replacement CURT trailer hitch hardware from eTrailer for this hitch and installed the 11074 on my 2009 4DR Rabbit. However - after install, I now experience a lot more noise at low RPMs. Theres vibration being transmitted back...

Troubleshooting Turn and Brake Lights not Working with Running Lights on, 2009 Volkswagen Rabbit

I have the same problem than the VW GTI guy. After I have wired the kit according to the 2-wire method into my 2009 Rabbit, turn and stop light are working as long as the running light is not on. I have tried also the different 3-wire methods...

Aero Bar Rhino Rack Roof Rack that Fits 2009 Volkswagen Rabbit 5 Door Hatch

Hello, I am looking at RR56RR for my 2009 Volkswagen Rabbit 3 door. Your site says it will fit but when I use the part number RV0230B into rhino racks site it states its only for the 5 door car. Which is correct? I really want these for my...

Hitch Options for a 1982 Dodge Rampage

Hello I have a 1982 Dodge rampage Car/pick up. S64025 is the best product for my application? | For your vehicle I believe your best option for installing a hitch would be to contact a qualified fabricator and have them custom fabricate a hitch. The...