!Designer Camper  x   >   !Range Rover  x   >   Toledo  x   >  

Balcrank 16006 2inch my question is can we convert this to a 2 5/16 ball both are Rated 5000lbs | We have a very similar coupler to the Balcrank 16006 you have that has a 2-5/16 inch ball and is for drum brakes but at this time we do not have...

I have this same set up on a trailer that we use for work and I believe the shock that is supposed to dampen the slide action when you stop has went out. Im needing to find this shock. yall show one for the 5000 lbs system with a 2 in ball...

Hello, I purchased a Rettig 16foot tandem axle trailer in a tractor deal and the trailer seems to have some sort of surge brake system. The brakes do not work and I am looking to repair them. The system looks similar to Demco Hydraulic brake...

Is it possible to buy a rebuild kit for this master cylinder? | We have a few different parts for Toledo actuators but not a master cylinder rebuild kit. We have the master cylinder that you referenced, # 10614. We also have a replacement shock,...

replacement actuator shocks | It looks like you are looking for a replacement shock for your actuator. We have several models including # 1844-2. This particular model fits Toledo brand actuators. When fully closed it measures 6-1/4 inches from...

Balcrank Actuator 16030. I have the subject actuator mounted on a three-inch wide straight frame. The master cylinder and the shock absorber replacements for the Balcrank 16006 which is the Balcrank TA6 Toledo A-Frame Actuator look similar....

Looking for a shock for my surge brake actuator. On the old shock is says MAECO 19277 and 8D76. it measures eye to eye compressed 7 1/4 and extended 9 1/4. It looks similar to your Item # 1844-2 for Toledo surge brake. Mine says SUR ACT III...

I recently purchased the trailer with this actuator on it, and I do not know how to test the surge brake actuator to make sure its working effectively. Is there a manual or a procedure that I could use to verify its working as it should? |...

What is the diameter of your shock # 1844-2? | I went out into our warehouse and measured the diameter of the Replacement Shock Absorber # 1844-2 and found that it measures 1-1/2 inches in diameter. |

Can anyone tell me who manufactures Toledo Master Cylinders, I have looked all over the web but there is no company who seems to own that brand and Toldeo themselves dont seem to have an office over here! | The brand Toledo that makes the part...

Is there a video on replacing the damper? | I have attached a link to a video that shows how the Replacement Shock Absorber, part # 1844-2 is installed. When this shock is collapsed it measures 6-1/4 inches from center of hole to center of...

I have a Reliable Tongue assembly with the shock damper that is not working. Do you have anything that will cross over? | One of our replacement shocks might work for your Reliable actuator but we do not carry that particular brand so you would...

Can you give me the inside and outside diameter of this bushing? Thank You. | Nylon Pivot Bushing # 1745 measures: Inner Diameter: 0.680 inches Outer Diameter of main sleeve: 0.810 inches Outer Diameter of flange: 0.993 inches Total Length:...

I have a Balcrank and I need a replacement master cylinder | The Replacement Master Cylinder # 10614 will fit Balcrank T-6 actuators for drum brakes. You will need to reuse your existing mounting hardware. |

Im searching for brake parts for my trailer. In particular a new coupler, master cylinder and brake hardware if available. Ive searched the model number with no success. If you have any parts available or suggestions I would appreciate any help...

does this master cylinder come with the boot to cover the plunger end of the master cylinder or do you the part # for it? | The product picture of the Master Cylinder # 10614 does not show the boot that comes with it, but if you check out the...

Is there a rebuild kit for this brake actuator available? I see the previous guy asked the same question. Im wondering if you guys were able to maybe Source One. Mine is not leaking but I took it apart to clean it out and I feel like it would...

Can you give me some dimensions for your surge brake shock #1844-2? *What is the width of the mounting tube that goes through the rubber bushing at each end? The one Im trying to replace is 1-1/4. *What is the diameter of the body of the...

Hi, I am trying to help a customer. He has a trailer with a Gabriel Brake actuator the number stamped on the top is 610712 T4HC He is looking for a shock absorber for this. Can you let me know if there is another model actuator that has a shock...

What size is the eyelet, i.e. bolt size used for this shock absorber. Do you have any other shocks that are similar with a 3 stroke, 7 inch collapse and 10 extended of same style with 7/16 mtg holes? | The bolt holes for the Replacement Shock...

Hi, I have a M101A3 military trailer. Are you able to confirm if the following parts are compatible? -Master Cylinder for Toledo Brake Actuators - 10614 -Replacement Shock Absorber for Toledo Brake Actuators - 1844-2 - Wheel Cylinder - 10inch...

I have the shock absorption shocks on my hydraulic trailer brakes when I come to a stop it does not slam but when I take off its slams hard pulling the slack out of the tongue. I was wondering if thats indication that I do need new shocks on...

Is there any way to modify a hydraulic drum brake actuator for my trailer? I have a 6,000lb actuator on about a 4,000 trailer. The brakes work, but could use some more power. | I do have an option available for you however, I cannot recommend...

have a boat trailer surge brake with a Gabriel mpd 85746 shock on it. is there a replacement shock I can use ? I can not find one on the internet | The best recommendation I can give you since we don't carry the Gabriel actuators would be to...