!CX-9  x   >   Deka  x   >   !Brave Motorhome  x   >  

The 12v constant is not hot on my 7pin trailer. I tested it with a multimeter. The trailer seems to be in good working orderI hooked it up to a buddies truck. I have no 30a fuse in the #2 spot marked Trailer lights of my underhood fuse box....

I am installing a new RV roof vent: Fan-Tastic Vent 801250 in my 16foot Casita. The original vent did not have power, so there is no wiring coming to the cutout. I need to figure out a way to wire the vent. There is black and white wiring...

6 volt vehicle 1953 Ford sedan pulling somewhat newer travel trailer with 12 volt brakes Is there any way to do this, or would I have to convert the trailer to 6 volt brakes? If conversion is necessary, can I get 6 volt brakes anymore? Thank...

2003 Sundowner horse trailer working lights not working Brakes, turn all work but the interior,side door, rear working lights do not come on... Any advice provided would be great! I am pulling it with a 2016 Silverado 2500hd. Thanks | It...

My brake device marks e2, disconnected it and marked e1 and I pressed the button that is in the | It sounds like you may have the Hopkins Towing Solutions Trailer Brake Controller part 47285 as this would make sense for the E1 and E2 codes you...

I have a customer with a 4 horse living quarters trailer with electric over hydraulic brakes. He is towing it with a early 2000 model Volvo semi tractor. He wants brake controler in the truck. Is the Tekonsha Prodigy RF remote system a good...

Controller works fine for a while then shows So? I cant seem to find any answers on this | The troubleshooting guide for the (discontinued) Draw-Tite Activator II 5500 is actually the same as the Draw-Tite Activator IV # 5504. The instructions...

Hello I have the Primus iq not sure which model it is. My trailer lights all work , but I get no voltage at the blade terminal for the electric brake. I unplugged the controller and used a jumper wire from the black wire to the blue wire and...

i have a factory brake controller but Im not getting any 12 volt battery charge at my 7 pin connecters at any time even with brakes actived | I am happy to help you troubleshoot the 12v pin not getting power on the 7-way connector. On some...

I have a Primus 90155 that I would like to install on a 2018 Ford T250 Cargo van. It has the tow package but no brake controller. Any help you can give would be awesome. Does my van have a plug under the dash etc. that makes it easy to hook...

My brakes on my trailer come on when I push on the brakes of my truck that dose not have an electric brake controller on it. What can I do | It sounds like your trailer connection is really needing some cleaning or your trailer has a brake controller...

Im gong off grid next week, i want to run 12v light in the popup. can i do that from 7 pin connector. how can i do that? Thank you, | It sounds like you are wanting to power a 12 volt light like the Optronics LED RV Interior Double Dome Light...

Is this jack wired to be able to hook up to a battery as well | The etrailer electric tongue jack # EJ-3527-BBX has a pre-wired 7-way plug like part # H20046 that saves you the hassle of hard-wiring the jack to its power source. It can receive...

going from a 4 way harness to a 7 way rv plug, does that still have the battery charge line? | The black wire of the 7-way adapter part # 37185 is for the battery charge line. To complete this circuit you'll need to run 10 gauge wire like part...

Can this be installed directly without a wired brake controller and use the Curt Echo instead? Assuming it would mean just wiring the trailer brake wire to the vehicles brake line directly. | You could use the # ETBC7 to just install the Curt...

I’m looking to hook up a brake/trailer lights controller and I do not have the connector under the dash. I have a wire that is specifically for trailer B+ but I don’t know how to wire it from there. | If you do not have the factory brake controller...

Is a 2007 Mirada already wired for a brake controller | To find this out you will need to either consult your owners manual or simply look around the dash and the steering column on the drivers side of your Mirada for a loose wiring harness....

I would like to add trailer brakes to my 13foot Scamp Camper. It has a torsion axle rated to 2200 lbs, and has the brake flange installed. The axle has the EZ Lube feature and the bearings are L44649 both inner and outer. The wheels are 13inch...

I have a small breakaway style battery on my trailer and I want to install an electric trailer jack I have the Husky HB4500. Can I simply power the jack from the tow vehicle 7 pin connector or do I need a separate larger battery? Thanks, |...

I am looking at purchasing a 5x10 ATC aluminum utility trailer. I am interested in having the stock Dexter torsion axles on the trailer replaced with Timbren Axles ASR3500S05 and was wondering what would be involved in doing this? I am planning...

I already installed one of your 4 pin connecters on my 2005 Pontiac Vibe My tear camper has Prodigy RF electronic brake control wich has a 7 way connecter. What do I need to convert over to a combination 4 pin and 7 pin connecter? | To add...

Hi. i want to tow my GMC Acadia 2007 behind a motorhome. Is there a wiring kit that I can just plug in the tail lights or do I have to strip the wires. | You need to splice into your Acadia's wiring to allow you to flat to it. I recommend...

I am replacing the wiring harness and all lights on my utility trailer and are considering using the following: 20 Ft 4-Way Trailer Wiring Harness - Wishbone Style - 30inch Ground - A20WB Optronics LED Clearance or Side Marker Light...

what size butt connectors for slt57rb andslt56rb | The lights you mentioned of # STL57RB and # STL56RB use 16 gauge wire so for butt connectors you'd want to use the blue ones like part # DW05744-5 which are for 16-14 gauge wires. |