Trailer Lights Specs:
Features:
2-1/2" x 1-1/4" x 13/16". Waterproof trailer light illuminates your license plate. Clear lens under polycarbonate housing. Surface mount - requires bracket (sold separately). Accepts standard 2-prong plug.
More Information >Trailer Lights Specs:
Features:
2-1/2" x 1-1/4" Rectangle. Waterproof LED trailer light illuminates your license plate. Requires mounting bracket or grommet (sold separately) for installation. 2-Wire pigtail with power and ground wires. Clear lens.
More Information >Trailer Lights Specs:
Features:
3" Diameter amber trailer reflector enhances visibility on the road. Designed for use on side or rear of your truck, trailer, or equipment. Durable polyester construction for outdoor use. Surface mount adhesive backing. J578 and J594 compliant
More Information >Trailer Lights Specs:
Features:
This 3" round, red reflective sticker is designed for use on the side or rear of your truck, trailer, or equipment. The tough polyester reflector stands up to outdoor use. Simple installation with adhesive backing. SAE J578 and J594 compliant.
More Information >Videos
for RV Exterior Lights
Help Articles
for RV Exterior Lights
Expert Answers
for RV Exterior Lights
Hey Gary, so the Yakima 54" Tracks for Roof Racks #Y26RR that you referenced are compatible with your setup as they provide the standard dimension roof tracks that your Sherpa Crows Nest was designed to fit. With that said the correct…
view full answer...I have a solution that may work for you, but we do not currently have any 3" diameter submersible reverse lights. Have a look at the Optronics Backup Light #BU45CB which is a 4-1/4" diameter light that can be mounted to your trailer…
view full answer...The Pollak switch part #PK34513 that you referenced would be a great option, but I'd rather recommend you go with the Buyers Products Toggle Switch with 2 Blade Terminals - Recessed Panel Mount #337SW911 as this setup was made for your…
view full answer...From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights…
view full answer...Hi Dan; I can definitely help you find these parts for your 2020 Grand Design Imagine 2500RL. I reached out to Dexter and found that the leaf springs that came with your axle measure 26" so you will want to match that when replacing them. Since…
view full answer...Yes, the 0.9 Cu Ft Greystone Standard RV Microwave - 900 Watts #324-000105 is a great replacement for your Advent model MW912B as the only real differences is the Greystone being 1/8" taller without the trim, and being about 1" less deep.…
view full answer...Hi Ken; I reached out to Lippert on this and they were unable to find the specific pressure from the #LC689052 testing. It is a large company and sometimes information gets lost across it with other brands like the Flow Max. I would say the pump is…
view full answer...I have a solution for you, but the main issue with puck style lights that mount to the surface of your RV ceiling or under cabinets, is that there aren't replacement bulbs available and they aren't really designed to have the bulbs replaced.…
view full answer...Did you pull any fuses or disconnect the battery before installing the Replacement Hydraulic Pump for Lippert Level Up Leveling Systems #LC58TF Vic? Have you tried unplugging and replugging the connector back in to see if a pin needed to be reseated?…
view full answer...You have a good eye as the black tubing sections are plastic for the Camco Gen-Turi RV Generator Exhaust System #CAM44461. It's just the curved pipe section that is made out of stainless steel.
view full answer...The side plates of the B&W gooseneck trailer hitch #BWGNRK1313 will mount on the outside of each frame rail of your 2004 Dodge 2500 8-foot bed. See the B&W video I included at the 7 min and 30 second mark. If your Firestone air bags like…
view full answer...The hole in the yellow octagon is offset from the center which when installed in the slotted hanger like the part #LC303918 gives you the ability to set an exact alignment with the other sides hanger but using the same configuration by simply…
view full answer...