Location of Brake Controller Fuse on a 2001 Chevy Silverado

Question

Question:

The cord from the trailer that connects to my truck was pinched. Had to splice it but still not getting lights when connected. need to check the fuse in the break controller. Where can I find the brake control fuse on a 2001 Chevrolet Silverado.

asked by: Debbie Y

0

Expert Reply:

Under the hood of your 2001 Chevy Silverado, remove the cover on the power distribution box. If standing in front of the truck facing the motor, the brake controller fuse will be that last large one in the back left corner, see picture.

But the brake controller fuse does not have anything to do with the trailer lights though. You will need to check the other tow package fuses, using the owner's manual to locate them, to see if any of them are blown.

There is likely an issue with the trailer connector, and you will need to take a look at it and possibly replace it with a new one. You can test the vehicle side connector to make sure it is functioning by using a circuit tester such as # PTW2993.

expert reply by: Michael H

0

click to enlarge

Answer 1

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 2

Great question. Without cutting a hole you wouldn't be able to get enough clearance for the jacks to work. I would strongly recommend using them on the outside to prevent clearance issues and probable damage. However, I think you would be better…

view full answer...

Answer 3

If your 2002 Chevrolet Silverado did not come wired with a 7-Way plug from the factory, you will need to connect the brake controller power wire and the electric brake wire underneath your hood to complete the brake controller installation. Once you…

view full answer...

Answer 4

There are some connections under the hood that will need to be made to complete the installation of the Tekonsha P2 Brake Controller #90885 with Wiring Harness, #3025-P. Once you have plugged in the #3025-P harness into the port to the left of the…

view full answer...

Answer 5

There are some tests you can do to determine where the problem is: brake controller, truck, or trailer. First, in the truck cab you will need to sever the blue wire several inches from the back of the controller. Then use a circuit tester such as…

view full answer...

Answer 6

Thank you for being very detailed with your question! The first step I would take is to make sure everything on the truck and trailer is wired properly. Your Prodigy brake controller should have the wiring adapter #3025-P which is custom for your…

view full answer...

Answer 7

The HydraStar Electric Over Hydraulic Actuator part #HBA16 has a 12 oz. fluid capacity and the Dexter DX Series Electric Over Hydraulic Brake Actuator part #K71-651 has a 22 oz. fluid capacity. That said, although the extra fluid capacity is nice the…

view full answer...

Answer 8

You can refer to the linked article concerning brake controller installation in a 1999-2006 Silverado to see the steps needed to activate power for brake controller installation. Under the heading "Step 2 - Under the Hood" there are photos…

view full answer...

Answer 9

You are correct, there are some connections that will need to be made under the hood of your 2001 Chevy Silverado 2500 in order to make the brake controller and possibly the 7-Way trailer connector fully functional. We actually have a detailed FAQ…

view full answer...

Answer 10

Unfortunately, the 1999 Tahoe does not have the port under the dash to plug in the brake controller wiring adapter. You will need to hardwire your controller. We have a how to pagethat you might find helpful, I have linked to it below. There are…

view full answer...

Answer 11

I would recommend that the breakaway cable be cut shorter than the safety chains/cables that way if the trailer were to come uncoupled from the hitch ball it would come to a stop without slamming into the back of the tow vehicle. For a breakaway…

view full answer...

Answer 12

The 4' of cable that comes with the Fastway Zip Coiled Trailer Breakaway Cable #FA80-01-2140 is actually standard for breakaway cables. If your trailer comes uncoupled then the chains should catch the coupler (which is why you criss-cross the…

view full answer...

Location of Brake Controller Fuse on a 2001 Chevy Silverado

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching