Will the Demco eZ-Latch Gooseneck Coupler Lower My 1995 WW Stock Trailer Another 4 to 5 Inches?
Updated 11/19/2026 | Published 11/06/2026 >
Products Featured in This Question
Question:
I have a 1995 W W 20foot stock trailer that I pull with a 2018 Ram 2500 pickup. The truck is too high for the trailer even after I cut 3inch off of the pedestal and lowered it as much as possible. The coupler that I have now is 9 1/2, would the DM73KV coupler and pedestal allow me to the front of the trailer another 4 or 5? The attached photo should explain it better than I did. My pedestal does not have holes for adjustment. Thank you.
asked by: Burton S
Expert Reply:
Hello Burton,
Welcome to etrailer, I'm glad you found us!
Thanks for sending the picture. I can see why you're looking for another 4 or 5 inches of adjustment, especially since you've already shortened your existing pedestal as much as possible.
I reached out to Demco about the eZ-Latch Gooseneck Coupler # DM73KV, and they mentioned that your 1995 WW stock trailer may have a custom-built setup that doesn't follow standard gooseneck coupler mounting configurations.
Demco would like to see a picture of the outer tube that your current coupler slides into, similar to the example I've included below. Their coupler requires a compatible outer tube with an adjustment pin. If yours doesn't have that pin, the # DM73KV won't work with your existing setup.
In that case, you would need to have your current outer tube removed and a compatible replacement, like the Demco Gooseneck Coupler Outer Tube # DM83KV, welded in place. If you're not a qualified welder, I've also attached our dealer locator so you can see if we have someone in your area we trust to handle the installation.
Do you happen to be a welder?
Product Page this Question was Asked From
Demco eZ-Latch Gooseneck Coupler - Round Inner Tube - 2-5/16" Ball - 30K GTW
- Gooseneck Coupler
- Coupler with Inner Tube Only
- Round Tube
- 30000 lbs GTW
- 2-5/16 Inch Gooseneck Ball
- Auto Latch
- Demco
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Q&A: Installation Time for Blue Ox BX1128 Flat Tow Base Plate Kit for 2016 Jeep Grand Cherokee
- Q&A: Is The Demco eZ-Latch Gooseneck Coupler DM43KV Safe To Use On A Dump Trailer?
- Q&A: Furrion Chill Cube Non Ducted AC with Oscillating Air Distribution Box for Improved RV Airflow
- Q&A: Can I Use the Demco eZ-Latch Gooseneck Coupler on My Texas Pride Gooseneck Trailer?
- Q&A: Size Of Square Tube On Bigfoot Hydraulic Trailer Jack
- Q&A: Can You Reuse Hubs/Drums and Braking Assemblies When Using the Timbren Axle-Less Trailer Suspension
- Q&A: Bulldog Gooseneck Coupler Recommendation to Lower Gooseneck Trailer Nose More
- Article: Trailer Wiring Diagrams
- Article: Trailer Lighting Requirements
- Article: Ram Trailer Tow Prep Package
- Article: Trailer Tire Sizing
- Article: The Best Electric Trailer Jacks of 2025
- Article: How to Accurately Measure Trailer Leaf Springs
- Article: How to Tell the Weight Rating of a Trailer Axle





Burton S.
11/18/2026
My trailer has the original coupler, pedestal, and outer tube. What I need to know is the length of the coupler DM73KV and any additional space needed on the pedestal because of the latching mechanism. It would be much easier to drill holes through the outer tube than replace the entire system. I am not a welder. thank you, Burton