Which MORryde X-Factor Works with the MORryde CRE3000 Cushioned Equalizers
Updated 09/28/2026 | Published 09/24/2026 >
Products Featured in This Question
Question:
Site drives me nuts! Need to get back to the morryde x factor brace that attaches to a cre3000. Have the leaf spring attachment one in basket already. Had it earlier but now cant find it. Multiple searches with no result.
asked by: Steven S
Expert Reply:
Hey Steven, sorry about our site being difficult. It drives me nuts at times too. Here's the MORryde X-Factor that works with the CRE3000 # MR27ZR equalizers,
X-Factor part # MR33WR. What trailer is this going on?

Paul S.
9/25/2026
I rebuilt the whole suspension on my 2014 Keystone Cougar 337fls after bending both axles going places I shouldn’t. It went from a 10,400 weight rating to a true 12,000 lbs. Dexter 6,000 lbs axle tubes, I already had a set of four 3,000 lbs 6 leaf springs and I had installed a wet bolt kit. I added the X-Factor cross brace on the front and rear spring mounts. I figured that’s where the most torque would be. I did take it to a spring shop in Tucson to have everything aligned and they removed the axles to straighten them. Once that was done I installed five Milestar Steelpro Ast Trailer Tire - ST235/85R16 14 ply. It rides and pulls much better.


Tony S.
9/25/2026
I recently upgraded my stock suspension with the MORryde X-Factor crossmember and the CRE3000, and I highly recommend this upgrade if you get the chance. It saved me from a lot of drama while traveling from Oregon to Florida, back through Texas, and then home to Oregon. If you do the upgrade, don't forget to also get the UO12-016 MORryde Heavy Duty Shackle and Wet Bolt Kit.


Bill
9/25/2026
I just completed the install, Morryde equalizer, 1/2" shackle kit with wet bolt as well as 3 Xfactor cross members, out for a test run tomorrow. easy install, I did one side at a time. the rig is a 24' stealth toy hauler with a GVW of 11k.


Wayne
9/25/2026
Was very pleased, worked out great. I would recommend.

Product Page this Question was Asked From
MORryde X-Factor Crossmember for Standard Frame Hangers
- Accessories and Parts
- Trailer Suspension Parts
- Crossmember
- MORryde
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: MORryde X-Factor Crossmember for Standard Frame Hangers
- Q&A: Does the X-Factor Crossmember for Standard Frame Hangers Require Longer Suspension Bolts?
- Q&A: X-Factor and Wet Bolt Kit for 2022 Montana High Country 331RL
- Q&A: Which Hangers Should MORryde X-Factor Crossmembers Install On
- Q&A: Can MORryde X-Factor and Roadmaster Comfort Ride Systems be Installed Together?
- Q&A: Which MORryde X-Factor Can be Used with CRE3000 MORryde Equalizer Kit 2022 Grand Design Imagine
- Q&A: Can I Install Just One MORryde X-Factor Crossmember Or Do I Need All Three?
- Q&A: What is the Difference Between the MORryde CRE3000 and AllTrek 4000 Suspension Kits
- Article: Trailer Wiring Diagrams
- Article: 4 Steps to Choosing Your 5th Wheel Pin Box
- Article: Double-Eye Trailer Suspension System Review
- Article: 5 Tell-Tale Signs It’s Time to Replace Your Trailer’s Leaf Springs
- Article: How to Accurately Measure Trailer Leaf Springs
- Article: RV AC Not Cooling? What's Normal, What to Check, and When to Replace
- Article: How (and Where) to Connect an RV Propane Grill



Ed S.
9/25/2026
Yes, this one worked with my Montana with cre 3000 equilizer in middle. I used the drop down in the forward spring hanger BECAUSE I had to clear a drain pipe. I installed the standard in middle & rear spring hangers, it reinforced them all. I hear its the rear that take the most pressure when turning.