Can I Put Wheels on Your etrailer Square Sidewind Trailer Jack to Lift and Move Heavy Tables?
Updated 08/13/2026 | Published 08/07/2026 >
Products Featured in This Question
Question:
This jack would fit an application for us. We need to lift a long table off of its guide rails and then push it to another part of the plant. The floor is smooth concrete but we do have plastic pellets on the floor which would cause a side load on the jack when we are pushing it. We would attach wheels to each of four jacks. Due to the clearances under the table, the stroke of the jack would need to be 4 6 inches and not 13. Is it possible for you to do custom work like this? We will need 12 total to installation our three tables. Or is there another jack that might fit the requirements! For us, we need to lift the tables 4 to 6 inches. We are looking at higher weights for the additional side loads that we may encounter when pushing the tables.
asked by: Paul K
Expert Reply:
Hello Paul,
Thanks for writing in, and letting us help you with your custom project.
Thanks for sending over the additional picture and information. I got everything sent over to Dan in our Product Development Group, and after reviewing your application, he recommended using eight of the etrailer Boat Trailer Jack w/ Wheel # MJ-1500B instead of trying to modify the # TJDDP-20000SP-F.
For this application, Dan's recommendation would be to use two of the # MJ-1500B jacks at each corner of the table. They can be bolted in place, or welded on if that works better for your setup. If you decide to weld them, you'll just want to properly prep the mounting surfaces and use the appropriate PPE.
This setup will give you the lift and wheels you're looking for without having to custom-build the larger square jack. You would need eight jacks per table, so for all three tables you would need 24 of the # MJ-1500B.
I really appreciate you sending over the additional information and picture. It gave us a much better idea of what you're working with. Once you get everything set up, I'd love to hear how the jacks work out for moving the tables around your plant!
What kind of work are you guys doing with these tables at the plant? Or is it top secret =)
Product Page this Question was Asked From
etrailer Square Sidewind Trailer Jack - Foot Release Drop Leg - 13-1/2" Lift - 12,000 lbs
- Trailer Jack
- 5th Wheel Trailer
- Car Hauler
- Enclosed Trailer
- Gooseneck Trailer
- Side-Mount Jacks
- Sidewind Jack
- 10001 lbs or More
- Manual Jack
- 26-1/2 Inch Lift
- Weld-On
- With Rectangle Foot
- etrailer
more information >
Continue Researching
- Q&A: TJD-12000-HD Jack Handle Compatibility with TJDDP-20000SP-F Jack
- Q&A: Replacement Axle For a Stealth 7.5X12 Cargo Trailer 3,500-lb 93.5" Hub Face 77.5" Spring Center
- Q&A: Testing Electric Trailer Brakes Using Direct Battery Power
- Q&A: Testing Electric Brakes on Trailer without Connecting to Tow Vehicle
- Q&A: Replacement Screw and Nut for Bulldog 10K / 12K Square Trailer Jack
- Q&A: How to Install 12K etrailer Square Direct Weld Jack
- Q&A: Optronics Mini Red LED Clearance or Side Marker Light MCL131CR3B
- Article: Practice Safe Trailer Towing with These 4 Tips
- Article: 5 Tell-Tale Signs It’s Time to Replace Your Trailer’s Leaf Springs
- Article: Trailer Lighting Requirements
- Article: Replacing the Bearing, Races and Seals on a Trailer Hub
- Article: Best 5th Wheel to Gooseneck Adapters (2023)
- Article: Printable Trailer Bolt Hole Pattern Template
- Article: Trailer Jacks

