How to Install 12K etrailer Square Direct Weld Jack
Updated 11/14/2025 | Published 10/06/2022 >
Question:
How do I install this?
asked by: Ingrid
0
Expert Reply:
The Square Direct Weld Jack # TJDDP-20000SP-F will need to be welded on to the trailer frame by an experienced welder. So if you're using this to replace an old jack then you'll need to cut off the old jack and have this installed by welding.
Attached is a review video for you to check out.
expert reply by:
Jon G
0
Product Page this Question was Asked From
etrailer Square Sidewind Trailer Jack - Foot Release Drop Leg - 13-1/2" Lift - 12,000 lbs
- Trailer Jack
- 5th Wheel Trailer
- Car Hauler
- Enclosed Trailer
- Gooseneck Trailer
- Side-Mount Jacks
- Sidewind Jack
- 10001 lbs or More
- Manual Jack
- 26-1/2 Inch Lift
- Weld-On
- With Rectangle Foot
- etrailer
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: etrailer Square Sidewind Trailer Jack - Foot Release Drop Leg - 13-1/2" Lift - 12,000 lbs
- Search Results: gooseneck trailer jack drill adapter
- Search Results: 12x2 brake drums 7000 dexter
- Search Results: trailer jack
- Q&A: TJD-12000-HD Jack Handle Compatibility with TJDDP-20000SP-F Jack
- Shop: etrailer Square Sidewind Trailer Jack - Drop Leg - 12-3/8" Lift - 10,000 lbs
- Video: Review of etrailer Trailer Jack - TJDDP-20000SP-F
- Shop: etrailer Dual-Pin Two-Speed Square Tube Jack - 13-1/2" Lift - 12,000 lbs
- Search Results: trailer break away cable
- Shop: Buyers Products Square Jack - Front Pin Drop Leg - 12-3/8" Lift - 10,000 lbs
- Shop: Replacement Sidewind Crank for etrailer and Ram Square, Direct Weld Jacks
- Shop: Gooseneck Coupler Head Kit
- Search Results: etrack chock
- Video: Review of Dexter Trailer Bearings Races Seals Caps - Axle EZ Lube Grease Caps 2.72 Inch OD - DX49HR
- Q&A: Testing Electric Trailer Brakes Using Direct Battery Power
- Q&A: Testing Electric Brakes on Trailer without Connecting to Tow Vehicle
- Shop: EZ Lube Grease Caps with 2.72" OD - Fits 12" x 2" Dexter 8-Bolt Hubs - Zinc - Qty
- Q&A: Replacement 12,000LB Landing Gear Jacks For 30' Gooseneck Trailer
- Q&A: How Does the Gooseneck Coupler Head Kit # GC-HEAD Install
- Video: Let’s Check Out the Gooseneck Coupler Head Kit
- Video: Square Direct Weld Jack: The Breakdown
- Video: Review of etrailer Replacement Sidewind Crank TJD-12000 Series Jack - TJD-12000-HD
- Video: etrailer and Ram Square Sidewind Crank Replacement Review
- Q&A: Does RAM Offer a Replacement Foot Lever For The Square Direct Weld Jack # TJDDP-20000SP-F?
- Q&A: etrailer Square Jack TJDDP-20000SP-F - What Is The Size Of The Leg?
- Video: Review of etrailer Replacement Power Unit - e25RV



Joe
11/13/2025
What's a estimated of cost to removing a 2-1/2” square 6000 lbs and replace a 4-3/8” square 12,000lbs trailer jack from a experience welder?